Electronics Worksheet: LEDs and Resistors

Electronics lesson 16: LEDs and their resistor · Set 322 · 40 questions

Remember (Long leg plus, resistor always): Long leg (anode) → +; short leg by the flat edge (cathode) → −. Backwards: no light. Always a series resistor; without one the LED may burn out. R = (supply V − LED V) ÷ current in A. Example: (5 − 2) ÷ 0.02 = 150 Ω.

1. 1.💡 Why does an LED need a resistor in series? (a) to store charge (b) to change its colour (c) to make it brighter (d) to limit the current
2. 2.💡 On an LED, is the longer leg the anode (+) or the cathode (−)? (a) anode (+) (b) cathode (−)
3. 3.True or false: on an LED, the longer leg is the anode (+). (a) True (b) False
4. 4.True or false: on an LED, the leg by the flat edge is the anode (+). (a) False (b) True
5. 5.💡 On an LED, is the leg by the flat edge the anode (+) or the cathode (−)? (a) anode (+) (b) cathode (−)
6. 6.True or false: on an LED, the shorter leg is the anode (+). (a) False (b) True
7. 7.💡 What does LED stand for? (a) large electric dial (b) low energy device (c) light energy dial (d) light-emitting diode
8. 8.💡 An LED is joined to a 5 V battery through a 330 Ω resistor; its long leg goes to the − side and its short leg to the + side. What happens? (a) does not light (b) may burn out (c) lights up
9. 9.💡 On an LED, is the round-side leg the anode (+) or the cathode (−)? (a) cathode (−) (b) anode (+)
10. 10.True or false: on an LED, the longer leg is the cathode (−). (a) True (b) False
11. 11.💡 A red LED uses 2 V and should get 10 mA. It runs from a 5 V supply. What resistor (in ohms) is needed in series?
12. 12.True or false: on an LED, the shorter leg is the cathode (−). (a) False (b) True
13. 13.True or false: on an LED, the leg by the flat edge is the cathode (−). (a) False (b) True
14. 14.💡 A blue LED uses 3 V and should get 10 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
15. 15.💡 What happens if an LED is put in backwards? (a) it makes a sound (b) it changes colour (c) it does not light (d) it lights brighter
16. 16.💡 An LED is joined to a 6 V battery through a 220 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) lights up (b) may burn out (c) does not light
17. 17.True or false: on an LED, the round-side leg is the anode (+). (a) True (b) False
18. 18.💡 A red LED (it uses 2 V) is joined with a 100 Ω resistor to a 2.5 V supply. What current flows (in mA)?
19. 19.💡 A red LED (it uses 2 V) is joined with a 300 Ω resistor to a 5 V supply. What current flows (in mA)?
20. 20.💡 A blue LED uses 3 V and should get 25 mA. It runs from a 12 V supply. What resistor (in ohms) is needed in series?
21. 21.💡 A red LED uses 2 V and should get 25 mA. It runs from a 5 V supply. What resistor (in ohms) is needed in series?
22. 22.💡 A red LED (it uses 2 V) is joined with a 300 Ω resistor to a 6.5 V supply. What current flows (in mA)?
23. 23.💡 An LED is joined to a 3 V battery through a 220 Ω resistor; the leg next to the flat edge of its rim goes to the + side. What happens? (a) lights up (b) does not light (c) may burn out
24. 24.💡 A red LED (it uses 2 V) is joined with a 200 Ω resistor to a 4 V supply. What current flows (in mA)?
25. 25.💡 A red LED (it uses 2 V) is joined with a 100 Ω resistor to a 3.5 V supply. What current flows (in mA)?
26. 26.💡 On an LED, is the shorter leg the anode (+) or the cathode (−)? (a) cathode (−) (b) anode (+)
27. 27.💡 A red LED (it uses 2 V) is joined with a 200 Ω resistor to a 6 V supply. What current flows (in mA)?
28. 28.💡 A blue LED uses 3 V and should get 25 mA. It runs from a 9 V supply. What resistor (in ohms) is needed in series?
29. 29.💡 An LED is joined to a 9 V battery with no resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) lights up (b) may burn out (c) does not light
30. 30.💡 A red LED uses 2 V and should get 20 mA. It runs from a 9 V supply. What resistor (in ohms) is needed in series?
31. 31.💡 An LED is joined to a 9 V battery with no resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) does not light (b) may burn out (c) lights up
32. 32.💡 An LED is joined to a 9 V battery through a 220 Ω resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) may burn out (b) lights up (c) does not light
33. 33.💡 An LED is joined to a 6 V battery through a 220 Ω resistor; the leg next to the flat edge of its rim goes to the + side. What happens? (a) does not light (b) lights up (c) may burn out
34. 34.💡 A blue LED uses 3 V and should get 20 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
35. 35.True or false: on an LED, the round-side leg is the cathode (−). (a) False (b) True
36. 36.💡 A red LED uses 2 V and should get 25 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
37. 37.💡 A blue LED uses 3 V and should get 25 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
38. 38.💡 An LED is joined to a 12 V battery with no resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) does not light (b) lights up (c) may burn out
39. 39.💡 An LED is joined to a 9 V battery through a 470 Ω resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) lights up (b) may burn out (c) does not light
40. 40.💡 A red LED (it uses 2 V) is joined with a 300 Ω resistor to an 8 V supply. What current flows (in mA)?

Free electronics lessons, practice and worksheets at talentjr.in/electronics-for-kids