Electronics Worksheet: LEDs and Resistors

Electronics lesson 16: LEDs and their resistor · Set 511 · 40 questions

Remember (Long leg plus, resistor always): Long leg (anode) → +; short leg by the flat edge (cathode) → −. Backwards: no light. Always a series resistor; without one the LED may burn out. R = (supply V − LED V) ÷ current in A. Example: (5 − 2) ÷ 0.02 = 150 Ω.

1. 1.💡 On an LED, is the shorter leg the anode (+) or the cathode (−)? (a) anode (+) (b) cathode (−)
2. 2.True or false: on an LED, the round-side leg is the cathode (−). (a) False (b) True
3. 3.💡 A red LED (it uses 2 V) is joined with a 300 Ω resistor to a 6.5 V supply. What current flows (in mA)?
4. 4.💡 A red LED uses 2 V and should get 20 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
5. 5.💡 An LED is joined to a 3 V battery through a 220 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) does not light (b) lights up (c) may burn out
6. 6.💡 On an LED, is the round-side leg the anode (+) or the cathode (−)? (a) cathode (−) (b) anode (+)
7. 7.💡 A blue LED uses 3 V and should get 10 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
8. 8.💡 A red LED (it uses 2 V) is joined with a 200 Ω resistor to a 5 V supply. What current flows (in mA)?
9. 9.💡 A red LED uses 2 V and should get 20 mA. It runs from a 9 V supply. What resistor (in ohms) is needed in series?
10. 10.💡 What does LED stand for? (a) light energy dial (b) light-emitting diode (c) large electric dial (d) low energy device
11. 11.💡 A red LED uses 2 V and should get 20 mA. It runs from a 12 V supply. What resistor (in ohms) is needed in series?
12. 12.True or false: on an LED, the shorter leg is the cathode (−). (a) True (b) False
13. 13.True or false: on an LED, the longer leg is the anode (+). (a) False (b) True
14. 14.💡 Why does an LED need a resistor in series? (a) to change its colour (b) to make it brighter (c) to store charge (d) to limit the current
15. 15.💡 A blue LED uses 3 V and should get 10 mA. It runs from a 9 V supply. What resistor (in ohms) is needed in series?
16. 16.💡 A blue LED uses 3 V and should get 20 mA. It runs from a 5 V supply. What resistor (in ohms) is needed in series?
17. 17.💡 An LED is joined to a 9 V battery through a 220 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) does not light (b) may burn out (c) lights up
18. 18.💡 A red LED (it uses 2 V) is joined with a 100 Ω resistor to a 3 V supply. What current flows (in mA)?
19. 19.💡 On an LED, is the leg by the flat edge the anode (+) or the cathode (−)? (a) anode (+) (b) cathode (−)
20. 20.💡 A red LED (it uses 2 V) is joined with a 150 Ω resistor to a 2.75 V supply. What current flows (in mA)?
21. 21.💡 On an LED, is the longer leg the anode (+) or the cathode (−)? (a) anode (+) (b) cathode (−)
22. 22.True or false: on an LED, the round-side leg is the anode (+). (a) True (b) False
23. 23.💡 An LED is joined to a 9 V battery through a 1000 Ω resistor; its long leg goes to the − side and its short leg to the + side. What happens? (a) lights up (b) may burn out (c) does not light
24. 24.💡 A blue LED uses 3 V and should get 10 mA. It runs from a 12 V supply. What resistor (in ohms) is needed in series?
25. 25.True or false: on an LED, the shorter leg is the anode (+). (a) True (b) False
26. 26.💡 What happens if an LED is put in backwards? (a) it lights brighter (b) it makes a sound (c) it does not light (d) it changes colour
27. 27.💡 An LED is joined to a 5 V battery with no resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) does not light (b) lights up (c) may burn out
28. 28.💡 An LED is joined to a 9 V battery through a 1000 Ω resistor; the leg next to the flat edge of its rim goes to the + side. What happens? (a) lights up (b) does not light (c) may burn out
29. 29.True or false: on an LED, the longer leg is the cathode (−). (a) True (b) False
30. 30.💡 An LED is joined to a 5 V battery through a 1000 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) does not light (b) lights up (c) may burn out
31. 31.💡 A red LED (it uses 2 V) is joined with a 200 Ω resistor to a 3 V supply. What current flows (in mA)?
32. 32.True or false: on an LED, the leg by the flat edge is the cathode (−). (a) True (b) False
33. 33.💡 A red LED uses 2 V and should get 25 mA. It runs from a 5 V supply. What resistor (in ohms) is needed in series?
34. 34.💡 An LED is joined to a 9 V battery with no resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) may burn out (b) lights up (c) does not light
35. 35.💡 An LED is joined to a 9 V battery through a 220 Ω resistor; its long leg goes to the − side and its short leg to the + side. What happens? (a) does not light (b) lights up (c) may burn out
36. 36.💡 An LED is joined to a 9 V battery through a 470 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) lights up (b) does not light (c) may burn out
37. 37.💡 A red LED (it uses 2 V) is joined with a 300 Ω resistor to a 5 V supply. What current flows (in mA)?
38. 38.💡 A red LED uses 2 V and should get 20 mA. It runs from a 5 V supply. What resistor (in ohms) is needed in series?
39. 39.💡 A blue LED uses 3 V and should get 25 mA. It runs from a 5 V supply. What resistor (in ohms) is needed in series?
40. 40.💡 An LED is joined to a 3 V battery through a 470 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) lights up (b) may burn out (c) does not light

Free electronics lessons, practice and worksheets at talentjr.in/electronics-for-kids