Electronics Worksheet: LEDs and Resistors

Electronics lesson 16: LEDs and their resistor · Set 653 · 40 questions

Remember (Long leg plus, resistor always): Long leg (anode) → +; short leg by the flat edge (cathode) → −. Backwards: no light. Always a series resistor; without one the LED may burn out. R = (supply V − LED V) ÷ current in A. Example: (5 − 2) ÷ 0.02 = 150 Ω.

1. 1.💡 A red LED uses 2 V and should get 10 mA. It runs from a 12 V supply. What resistor (in ohms) is needed in series?
2. 2.💡 A red LED (it uses 2 V) is joined with a 100 Ω resistor to a 4 V supply. What current flows (in mA)?
3. 3.💡 On an LED, is the shorter leg the anode (+) or the cathode (−)? (a) anode (+) (b) cathode (−)
4. 4.💡 A blue LED uses 3 V and should get 20 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
5. 5.💡 On an LED, is the round-side leg the anode (+) or the cathode (−)? (a) cathode (−) (b) anode (+)
6. 6.True or false: on an LED, the longer leg is the anode (+). (a) True (b) False
7. 7.True or false: on an LED, the longer leg is the cathode (−). (a) True (b) False
8. 8.💡 What does LED stand for? (a) light energy dial (b) large electric dial (c) low energy device (d) light-emitting diode
9. 9.💡 A red LED uses 2 V and should get 20 mA. It runs from a 9 V supply. What resistor (in ohms) is needed in series?
10. 10.💡 What happens if an LED is put in backwards? (a) it changes colour (b) it does not light (c) it lights brighter (d) it makes a sound
11. 11.True or false: on an LED, the round-side leg is the cathode (−). (a) True (b) False
12. 12.True or false: on an LED, the round-side leg is the anode (+). (a) False (b) True
13. 13.💡 An LED is joined to a 5 V battery with no resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) lights up (b) may burn out (c) does not light
14. 14.💡 A red LED (it uses 2 V) is joined with a 300 Ω resistor to an 8 V supply. What current flows (in mA)?
15. 15.True or false: on an LED, the leg by the flat edge is the cathode (−). (a) True (b) False
16. 16.💡 On an LED, is the longer leg the anode (+) or the cathode (−)? (a) anode (+) (b) cathode (−)
17. 17.💡 An LED is joined to a 5 V battery through a 220 Ω resistor; its long leg goes to the − side and its short leg to the + side. What happens? (a) may burn out (b) does not light (c) lights up
18. 18.💡 An LED is joined to a 3 V battery through a 330 Ω resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) may burn out (b) lights up (c) does not light
19. 19.💡 An LED is joined to a 6 V battery through a 1000 Ω resistor; the leg next to the flat edge of its rim goes to the + side. What happens? (a) does not light (b) may burn out (c) lights up
20. 20.💡 An LED is joined to a 9 V battery with no resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) does not light (b) may burn out (c) lights up
21. 21.💡 An LED is joined to a 5 V battery through a 470 Ω resistor; its long leg goes to the − side and its short leg to the + side. What happens? (a) does not light (b) lights up (c) may burn out
22. 22.💡 An LED is joined to a 6 V battery through a 330 Ω resistor; its long leg goes to the + side and its short leg to the − side. What happens? (a) does not light (b) lights up (c) may burn out
23. 23.💡 On an LED, is the leg by the flat edge the anode (+) or the cathode (−)? (a) cathode (−) (b) anode (+)
24. 24.True or false: on an LED, the shorter leg is the cathode (−). (a) True (b) False
25. 25.💡 A red LED (it uses 2 V) is joined with a 150 Ω resistor to a 2.75 V supply. What current flows (in mA)?
26. 26.💡 A red LED uses 2 V and should get 25 mA. It runs from a 12 V supply. What resistor (in ohms) is needed in series?
27. 27.💡 Why does an LED need a resistor in series? (a) to store charge (b) to limit the current (c) to make it brighter (d) to change its colour
28. 28.💡 An LED is joined to a 3 V battery through a 330 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) does not light (b) lights up (c) may burn out
29. 29.True or false: on an LED, the leg by the flat edge is the anode (+). (a) True (b) False
30. 30.💡 An LED is joined to a 3 V battery through a 220 Ω resistor; its long leg goes to the − side and its short leg to the + side. What happens? (a) does not light (b) may burn out (c) lights up
31. 31.💡 A red LED uses 2 V and should get 10 mA. It runs from a 9 V supply. What resistor (in ohms) is needed in series?
32. 32.💡 A blue LED uses 3 V and should get 20 mA. It runs from a 12 V supply. What resistor (in ohms) is needed in series?
33. 33.💡 An LED is joined to a 9 V battery through a 330 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) does not light (b) may burn out (c) lights up
34. 34.💡 An LED is joined to a 9 V battery through a 220 Ω resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) lights up (b) does not light (c) may burn out
35. 35.💡 A red LED uses 2 V and should get 10 mA. It runs from a 6 V supply. What resistor (in ohms) is needed in series?
36. 36.💡 A blue LED uses 3 V and should get 25 mA. It runs from a 12 V supply. What resistor (in ohms) is needed in series?
37. 37.💡 An LED is joined to a 6 V battery through a 220 Ω resistor; the leg next to the flat edge of its rim goes to the + side. What happens? (a) lights up (b) does not light (c) may burn out
38. 38.💡 An LED is joined to a 12 V battery with no resistor; the leg next to the flat edge of its rim goes to the − side. What happens? (a) lights up (b) may burn out (c) does not light
39. 39.💡 An LED is joined to a 3 V battery through a 330 Ω resistor; its long leg goes to the − side and its short leg to the + side. What happens? (a) does not light (b) lights up (c) may burn out
40. 40.💡 A red LED (it uses 2 V) is joined with a 200 Ω resistor to a 4 V supply. What current flows (in mA)?

Free electronics lessons, practice and worksheets at talentjr.in/electronics-for-kids