Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 126 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.True or false: to let adults use hot glue is not safe. (a) False (b) True
2. 2.🔧 Which tool would you use to measure a long length? (a) pliers (b) a protractor (c) a saw (d) a tape measure
3. 3.Which job is a protractor for? (a) drive in a nail (b) make a hole in wood (c) check a shelf is level (d) measure an angle
4. 4.Which job is a saw for? (a) grip and bend wire (b) measure a long length (c) make a hole in wood (d) cut a wooden plank
5. 5.🔍 Which is the odd one out? (a) wear safety goggles (b) tie back long hair (c) cut towards your hand (d) cut away from your body
6. 6.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
7. 7.🦺 How should you carry scissors? (a) while running (b) points up, open (c) points down, closed (d) by the blades
8. 8.True or false: to drive in a nail, use a hammer. (a) True (b) False
9. 9.True or false: to measure a long length, use a protractor. (a) True (b) False
10. 10.True or false: to put tools back after use is safe. (a) False (b) True
11. 11.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) nothing (c) a cap (d) safety goggles
12. 12.Which job is pliers for? (a) measure an angle (b) make a hole in wood (c) grip and bend wire (d) turn a screw
13. 13.🔧 Which tool would you use to grip and bend wire? (a) a tape measure (b) a spanner (c) pliers (d) a hand drill
14. 14.🔧 Which tool would you use to check a shelf is level? (a) a spirit level (b) pliers (c) sandpaper (d) a tape measure
15. 15.🔧 Which tool would you use to measure an angle? (a) a saw (b) a spanner (c) sandpaper (d) a protractor
16. 16.🔧 Which tool would you use to smooth a rough edge? (a) a protractor (b) a saw (c) sandpaper (d) a hand drill
17. 17.True or false: to cut away from your body is not safe. (a) True (b) False
18. 18.True or false: to leave tools on the floor is safe. (a) True (b) False
19. 19.True or false: to cut a wooden plank, use sandpaper. (a) True (b) False
20. 20.🦺 In the workshop, is it safe to let adults use hot glue? (a) safe (b) not safe
21. 21.Which job is a tape measure for? (a) measure a long length (b) tighten a nut (c) measure an angle (d) drive in a nail
22. 22.🔍 Which is the odd one out? (a) run while holding tools (b) let adults use hot glue (c) cut away from your body (d) tie back long hair
23. 23.True or false: to drive in a nail, use a tape measure. (a) False (b) True
24. 24.True or false: to make a hole in wood, use a hand drill. (a) False (b) True
25. 25.True or false: to touch a hot glue tip is not safe. (a) True (b) False
26. 26.True or false: to tighten a nut, use a spanner. (a) False (b) True
27. 27.🦺 In the workshop, is it safe to clamp wood before sawing? (a) safe (b) not safe
28. 28.True or false: to wear safety goggles is not safe. (a) False (b) True
29. 29.🔍 Which is the odd one out? (a) leave tools on the floor (b) cut away from your body (c) play near a moving drill (d) use a cracked tool
30. 30.🔍 Which is the odd one out? (a) clamp wood before sawing (b) use a cracked tool (c) run while holding tools (d) touch a hot glue tip
31. 31.True or false: to cut a wooden plank, use a saw. (a) True (b) False
32. 32.True or false: to measure a long length, use a tape measure. (a) False (b) True
33. 33.🦺 In the workshop, is it safe to use a cracked tool? (a) safe (b) not safe
34. 34.🔧 Which tool would you use to turn a screw? (a) a screwdriver (b) a hand drill (c) a spirit level (d) a spanner
35. 35.🔧 Which tool would you use to tighten a nut? (a) a tape measure (b) a hammer (c) a spanner (d) pliers
36. 36.True or false: to run while holding tools is not safe. (a) True (b) False
37. 37.🔍 Which is the odd one out? (a) cut towards your hand (b) use a cracked tool (c) leave tools on the floor (d) tie back long hair
38. 38.True or false: to turn a screw, use a spanner. (a) False (b) True
39. 39.🔧 Which tool would you use to cut a wooden plank? (a) pliers (b) a screwdriver (c) sandpaper (d) a saw
40. 40.🦺 In the workshop, is it safe to cut away from your body? (a) safe (b) not safe

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids