← Tools and workshop safety lesson New set →

Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 130 · 40 questions
TalentJR

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

NameDateTime takenScore ___ / 40
  1. 1.True or false: to cut away from your body is safe. (a) True (b) False
  2. 2.🦺 In the workshop, is it safe to tie back long hair? (a) safe (b) not safe
  3. 3.🔍 Which is the odd one out? (a) clamp wood before sawing (b) let adults use hot glue (c) cut away from your body (d) leave tools on the floor
  4. 4.Which job is sandpaper for? (a) grip and bend wire (b) cut a wooden plank (c) smooth a rough edge (d) drive in a nail
  5. 5.🦺 How should you carry scissors? (a) by the blades (b) while running (c) points up, open (d) points down, closed
  6. 6.Which job is a hand drill for? (a) make a hole in wood (b) check a shelf is level (c) tighten a nut (d) grip and bend wire
  7. 7.🦺 What protects your eyes when sawing or drilling? (a) nothing (b) safety goggles (c) sunglasses (d) a cap
  8. 8.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
  9. 9.🔍 Which is the odd one out? (a) run while holding tools (b) clamp wood before sawing (c) let adults use hot glue (d) carry scissors closed
  10. 10.Which job is a hammer for? (a) cut a wooden plank (b) drive in a nail (c) measure a long length (d) measure an angle
  11. 11.True or false: to wear safety goggles is not safe. (a) True (b) False
  12. 12.True or false: to cut a wooden plank, use a tape measure. (a) False (b) True
  13. 13.🔧 Which tool would you use to cut a wooden plank? (a) a saw (b) a hand drill (c) pliers (d) a spanner
  14. 14.True or false: to grip and bend wire, use sandpaper. (a) False (b) True
  15. 15.🦺 In the workshop, is it safe to put tools back after use? (a) safe (b) not safe
  16. 16.Which job is a tape measure for? (a) turn a screw (b) drive in a nail (c) grip and bend wire (d) measure a long length
  17. 17.Which job is a screwdriver for? (a) check a shelf is level (b) drive in a nail (c) measure a long length (d) turn a screw
  18. 18.True or false: to grip and bend wire, use a protractor. (a) False (b) True
  19. 19.🔧 Which tool would you use to check a shelf is level? (a) a screwdriver (b) a spirit level (c) pliers (d) a hammer
  20. 20.🔍 Which is the odd one out? (a) use a cracked tool (b) touch a hot glue tip (c) let adults use hot glue (d) run while holding tools
  21. 21.True or false: to measure an angle, use a hand drill. (a) True (b) False
  22. 22.True or false: to measure a long length, use a saw. (a) False (b) True
  23. 23.True or false: to cut towards your hand is safe. (a) True (b) False
  24. 24.True or false: to measure a long length, use pliers. (a) False (b) True
  25. 25.True or false: to turn a screw, use a screwdriver. (a) True (b) False
  26. 26.🔍 Which is the odd one out? (a) carry scissors closed (b) let adults use hot glue (c) wear safety goggles (d) touch a hot glue tip
  27. 27.True or false: to check a shelf is level, use a saw. (a) True (b) False
  28. 28.True or false: to measure a long length, use a tape measure. (a) True (b) False
  29. 29.True or false: to smooth a rough edge, use pliers. (a) True (b) False
  30. 30.True or false: to turn a screw, use a spanner. (a) True (b) False
  31. 31.True or false: to carry scissors closed is not safe. (a) False (b) True
  32. 32.True or false: to measure an angle, use sandpaper. (a) True (b) False
  33. 33.🔍 Which is the odd one out? (a) let adults use hot glue (b) clamp wood before sawing (c) carry scissors closed (d) use a cracked tool
  34. 34.Which job is a spirit level for? (a) grip and bend wire (b) tighten a nut (c) check a shelf is level (d) drive in a nail
  35. 35.🦺 In the workshop, is it safe to carry scissors closed? (a) safe (b) not safe
  36. 36.Which job is a saw for? (a) cut a wooden plank (b) measure an angle (c) turn a screw (d) drive in a nail
  37. 37.🦺 In the workshop, is it safe to use a cracked tool? (a) safe (b) not safe
  38. 38.🔧 Which tool would you use to tighten a nut? (a) a saw (b) a spanner (c) sandpaper (d) a hand drill
  39. 39.True or false: to use a cracked tool is not safe. (a) False (b) True
  40. 40.🔧 Which tool would you use to measure an angle? (a) a spirit level (b) a protractor (c) a tape measure (d) a hammer

Answer key

  1. True
  2. safe
  3. leave tools on the floor
  4. smooth a rough edge
  5. points down, closed
  6. make a hole in wood
  7. safety goggles
  8. not safe
  9. run while holding tools
  10. drive in a nail
  11. False
  12. False
  13. a saw
  14. False
  15. safe
  16. measure a long length
  17. turn a screw
  18. False
  19. a spirit level
  20. let adults use hot glue
  21. False
  22. False
  23. False
  24. False
  25. True
  26. touch a hot glue tip
  27. False
  28. True
  29. False
  30. False
  31. False
  32. False
  33. use a cracked tool
  34. check a shelf is level
  35. safe
  36. cut a wooden plank
  37. not safe
  38. a spanner
  39. True
  40. a protractor

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids