Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 132 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.Which job is a spirit level for? (a) make a hole in wood (b) check a shelf is level (c) smooth a rough edge (d) drive in a nail
2. 2.🦺 In the workshop, is it safe to tie back long hair? (a) safe (b) not safe
3. 3.True or false: to leave tools on the floor is safe. (a) False (b) True
4. 4.🦺 How should you carry scissors? (a) while running (b) points down, closed (c) points up, open (d) by the blades
5. 5.🔍 Which is the odd one out? (a) run while holding tools (b) tie back long hair (c) let adults use hot glue (d) cut away from your body
6. 6.True or false: to put tools back after use is safe. (a) True (b) False
7. 7.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) the youngest child (b) any child alone (c) an adult (d) a stranger
8. 8.True or false: to measure a long length, use a tape measure. (a) False (b) True
9. 9.🔧 Which tool would you use to measure an angle? (a) a protractor (b) a screwdriver (c) a spanner (d) a hand drill
10. 10.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) a cap (c) nothing (d) sunglasses
11. 11.🔍 Which is the odd one out? (a) touch a hot glue tip (b) leave tools on the floor (c) cut away from your body (d) play near a moving drill
12. 12.True or false: to clamp wood before sawing is not safe. (a) True (b) False
13. 13.True or false: to cut a wooden plank, use a hand drill. (a) False (b) True
14. 14.Which job is a hand drill for? (a) grip and bend wire (b) cut a wooden plank (c) drive in a nail (d) make a hole in wood
15. 15.Which job is a hammer for? (a) cut a wooden plank (b) turn a screw (c) measure a long length (d) drive in a nail
16. 16.True or false: to tighten a nut, use a spanner. (a) True (b) False
17. 17.True or false: to carry scissors closed is safe. (a) True (b) False
18. 18.🔧 Which tool would you use to tighten a nut? (a) a hammer (b) a spanner (c) a hand drill (d) pliers
19. 19.🔧 Which tool would you use to turn a screw? (a) a screwdriver (b) a spanner (c) a hand drill (d) a hammer
20. 20.🔧 Which tool would you use to smooth a rough edge? (a) pliers (b) a tape measure (c) sandpaper (d) a spirit level
21. 21.🦺 In the workshop, is it safe to put tools back after use? (a) safe (b) not safe
22. 22.True or false: to cut away from your body is not safe. (a) True (b) False
23. 23.True or false: to touch a hot glue tip is safe. (a) False (b) True
24. 24.🔧 Which tool would you use to drive in a nail? (a) a hand drill (b) a hammer (c) a saw (d) a screwdriver
25. 25.True or false: to measure a long length, use a protractor. (a) False (b) True
26. 26.Which job is sandpaper for? (a) turn a screw (b) measure a long length (c) smooth a rough edge (d) make a hole in wood
27. 27.Which job is a saw for? (a) make a hole in wood (b) tighten a nut (c) cut a wooden plank (d) smooth a rough edge
28. 28.True or false: to carry scissors closed is not safe. (a) False (b) True
29. 29.🔍 Which is the odd one out? (a) carry scissors closed (b) cut towards your hand (c) run while holding tools (d) use a cracked tool
30. 30.Which job is a tape measure for? (a) make a hole in wood (b) measure a long length (c) cut a wooden plank (d) smooth a rough edge
31. 31.True or false: to cut a wooden plank, use a saw. (a) True (b) False
32. 32.🦺 In the workshop, is it safe to leave tools on the floor? (a) safe (b) not safe
33. 33.Which job is a spanner for? (a) grip and bend wire (b) smooth a rough edge (c) make a hole in wood (d) tighten a nut
34. 34.Which job is a protractor for? (a) measure an angle (b) cut a wooden plank (c) check a shelf is level (d) smooth a rough edge
35. 35.🦺 In the workshop, is it safe to cut towards your hand? (a) safe (b) not safe
36. 36.🔍 Which is the odd one out? (a) put tools back after use (b) wear safety goggles (c) touch a hot glue tip (d) let adults use hot glue
37. 37.🦺 In the workshop, is it safe to carry scissors closed? (a) not safe (b) safe
38. 38.True or false: to measure an angle, use a protractor. (a) True (b) False
39. 39.True or false: to put tools back after use is not safe. (a) False (b) True
40. 40.Which job is pliers for? (a) measure a long length (b) check a shelf is level (c) grip and bend wire (d) make a hole in wood

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids