Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 135 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.True or false: to turn a screw, use a screwdriver. (a) False (b) True
2. 2.Which job is a hand drill for? (a) smooth a rough edge (b) make a hole in wood (c) drive in a nail (d) turn a screw
3. 3.🔍 Which is the odd one out? (a) play near a moving drill (b) clamp wood before sawing (c) put tools back after use (d) cut away from your body
4. 4.True or false: to measure an angle, use a protractor. (a) False (b) True
5. 5.🔧 Which tool would you use to measure a long length? (a) a tape measure (b) a hand drill (c) a hammer (d) a saw
6. 6.True or false: to touch a hot glue tip is not safe. (a) False (b) True
7. 7.Which job is a hammer for? (a) cut a wooden plank (b) drive in a nail (c) turn a screw (d) grip and bend wire
8. 8.True or false: to cut towards your hand is safe. (a) False (b) True
9. 9.🦺 In the workshop, is it safe to wear safety goggles? (a) safe (b) not safe
10. 10.🦺 In the workshop, is it safe to put tools back after use? (a) safe (b) not safe
11. 11.True or false: to leave tools on the floor is not safe. (a) True (b) False
12. 12.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) nothing (c) a cap (d) sunglasses
13. 13.🔧 Which tool would you use to measure an angle? (a) a hammer (b) a protractor (c) a screwdriver (d) pliers
14. 14.Which job is a screwdriver for? (a) turn a screw (b) smooth a rough edge (c) measure an angle (d) tighten a nut
15. 15.🔍 Which is the odd one out? (a) touch a hot glue tip (b) let adults use hot glue (c) clamp wood before sawing (d) put tools back after use
16. 16.🦺 In the workshop, is it safe to touch a hot glue tip? (a) not safe (b) safe
17. 17.🦺 In the workshop, is it safe to cut away from your body? (a) not safe (b) safe
18. 18.True or false: to drive in a nail, use a spirit level. (a) True (b) False
19. 19.Which job is sandpaper for? (a) drive in a nail (b) cut a wooden plank (c) grip and bend wire (d) smooth a rough edge
20. 20.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) a stranger (c) the youngest child (d) an adult
21. 21.🔧 Which tool would you use to drive in a nail? (a) a tape measure (b) a saw (c) a spirit level (d) a hammer
22. 22.🔍 Which is the odd one out? (a) tie back long hair (b) wear safety goggles (c) put tools back after use (d) run while holding tools
23. 23.🔍 Which is the odd one out? (a) wear safety goggles (b) carry scissors closed (c) let adults use hot glue (d) leave tools on the floor
24. 24.True or false: to cut a wooden plank, use a tape measure. (a) False (b) True
25. 25.🔍 Which is the odd one out? (a) clamp wood before sawing (b) carry scissors closed (c) cut towards your hand (d) wear safety goggles
26. 26.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe
27. 27.Which job is a spirit level for? (a) tighten a nut (b) check a shelf is level (c) drive in a nail (d) smooth a rough edge
28. 28.True or false: to cut away from your body is safe. (a) False (b) True
29. 29.🔍 Which is the odd one out? (a) use a cracked tool (b) tie back long hair (c) clamp wood before sawing (d) cut away from your body
30. 30.🔍 Which is the odd one out? (a) run while holding tools (b) use a cracked tool (c) play near a moving drill (d) tie back long hair
31. 31.🔧 Which tool would you use to smooth a rough edge? (a) sandpaper (b) a screwdriver (c) a tape measure (d) a saw
32. 32.🔧 Which tool would you use to make a hole in wood? (a) a tape measure (b) sandpaper (c) a hammer (d) a hand drill
33. 33.🔍 Which is the odd one out? (a) put tools back after use (b) cut towards your hand (c) leave tools on the floor (d) run while holding tools
34. 34.🔧 Which tool would you use to tighten a nut? (a) a hammer (b) a spanner (c) a saw (d) a spirit level
35. 35.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
36. 36.True or false: to turn a screw, use pliers. (a) True (b) False
37. 37.Which job is a tape measure for? (a) measure a long length (b) check a shelf is level (c) turn a screw (d) cut a wooden plank
38. 38.🔧 Which tool would you use to check a shelf is level? (a) pliers (b) a spirit level (c) a spanner (d) a hammer
39. 39.🔧 Which tool would you use to cut a wooden plank? (a) a saw (b) sandpaper (c) a tape measure (d) a spanner
40. 40.True or false: to smooth a rough edge, use sandpaper. (a) True (b) False

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids