Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 139 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.True or false: to cut towards your hand is safe. (a) False (b) True
2. 2.Which job is a tape measure for? (a) grip and bend wire (b) cut a wooden plank (c) measure an angle (d) measure a long length
3. 3.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) a cap (c) nothing (d) safety goggles
4. 4.🦺 How should you carry scissors? (a) points up, open (b) by the blades (c) while running (d) points down, closed
5. 5.🦺 In the workshop, is it safe to let adults use hot glue? (a) not safe (b) safe
6. 6.True or false: to tighten a nut, use a saw. (a) False (b) True
7. 7.🦺 In the workshop, is it safe to wear safety goggles? (a) safe (b) not safe
8. 8.Which job is a spirit level for? (a) smooth a rough edge (b) turn a screw (c) check a shelf is level (d) drive in a nail
9. 9.🔍 Which is the odd one out? (a) cut towards your hand (b) leave tools on the floor (c) use a cracked tool (d) cut away from your body
10. 10.🔧 Which tool would you use to check a shelf is level? (a) a tape measure (b) a hand drill (c) a saw (d) a spirit level
11. 11.🔧 Which tool would you use to measure a long length? (a) a tape measure (b) a saw (c) a hammer (d) a spanner
12. 12.🔧 Which tool would you use to make a hole in wood? (a) a hand drill (b) a protractor (c) a tape measure (d) a screwdriver
13. 13.🔍 Which is the odd one out? (a) play near a moving drill (b) use a cracked tool (c) let adults use hot glue (d) cut towards your hand
14. 14.True or false: to measure a long length, use a tape measure. (a) False (b) True
15. 15.True or false: to measure an angle, use a protractor. (a) False (b) True
16. 16.True or false: to cut a wooden plank, use a saw. (a) True (b) False
17. 17.🔧 Which tool would you use to cut a wooden plank? (a) a hand drill (b) a protractor (c) a screwdriver (d) a saw
18. 18.Which job is a hand drill for? (a) make a hole in wood (b) grip and bend wire (c) drive in a nail (d) measure a long length
19. 19.Which job is a protractor for? (a) measure a long length (b) make a hole in wood (c) measure an angle (d) grip and bend wire
20. 20.🔍 Which is the odd one out? (a) touch a hot glue tip (b) clamp wood before sawing (c) leave tools on the floor (d) play near a moving drill
21. 21.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
22. 22.🔍 Which is the odd one out? (a) cut away from your body (b) play near a moving drill (c) clamp wood before sawing (d) put tools back after use
23. 23.🔍 Which is the odd one out? (a) put tools back after use (b) cut away from your body (c) tie back long hair (d) leave tools on the floor
24. 24.🦺 In the workshop, is it safe to leave tools on the floor? (a) not safe (b) safe
25. 25.True or false: to turn a screw, use a screwdriver. (a) False (b) True
26. 26.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) a stranger (c) the youngest child (d) an adult
27. 27.🔍 Which is the odd one out? (a) leave tools on the floor (b) cut towards your hand (c) put tools back after use (d) run while holding tools
28. 28.🔧 Which tool would you use to turn a screw? (a) a spirit level (b) sandpaper (c) a spanner (d) a screwdriver
29. 29.True or false: to tighten a nut, use a hammer. (a) False (b) True
30. 30.True or false: to grip and bend wire, use pliers. (a) False (b) True
31. 31.🦺 In the workshop, is it safe to tie back long hair? (a) safe (b) not safe
32. 32.True or false: to cut a wooden plank, use a hammer. (a) True (b) False
33. 33.🦺 In the workshop, is it safe to use a cracked tool? (a) safe (b) not safe
34. 34.True or false: to measure an angle, use a tape measure. (a) True (b) False
35. 35.Which job is pliers for? (a) measure a long length (b) make a hole in wood (c) grip and bend wire (d) drive in a nail
36. 36.🔧 Which tool would you use to tighten a nut? (a) a spanner (b) a tape measure (c) a protractor (d) sandpaper
37. 37.True or false: to tighten a nut, use a spanner. (a) True (b) False
38. 38.🔍 Which is the odd one out? (a) let adults use hot glue (b) tie back long hair (c) clamp wood before sawing (d) use a cracked tool
39. 39.🦺 In the workshop, is it safe to carry scissors closed? (a) not safe (b) safe
40. 40.🔧 Which tool would you use to smooth a rough edge? (a) a tape measure (b) pliers (c) sandpaper (d) a spanner

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids