Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 149 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.True or false: to measure an angle, use a hand drill. (a) False (b) True
2. 2.True or false: to let adults use hot glue is safe. (a) False (b) True
3. 3.🔍 Which is the odd one out? (a) run while holding tools (b) use a cracked tool (c) touch a hot glue tip (d) cut away from your body
4. 4.True or false: to grip and bend wire, use a hammer. (a) True (b) False
5. 5.🦺 What protects your eyes when sawing or drilling? (a) nothing (b) a cap (c) safety goggles (d) sunglasses
6. 6.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
7. 7.🔍 Which is the odd one out? (a) touch a hot glue tip (b) carry scissors closed (c) tie back long hair (d) clamp wood before sawing
8. 8.🦺 In the workshop, is it safe to let adults use hot glue? (a) safe (b) not safe
9. 9.🔧 Which tool would you use to make a hole in wood? (a) a hand drill (b) a saw (c) a hammer (d) a protractor
10. 10.🦺 In the workshop, is it safe to clamp wood before sawing? (a) not safe (b) safe
11. 11.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) a stranger (b) the youngest child (c) an adult (d) any child alone
12. 12.🦺 In the workshop, is it safe to cut towards your hand? (a) safe (b) not safe
13. 13.Which job is pliers for? (a) check a shelf is level (b) measure a long length (c) make a hole in wood (d) grip and bend wire
14. 14.🔧 Which tool would you use to measure an angle? (a) a screwdriver (b) a spanner (c) a spirit level (d) a protractor
15. 15.🔧 Which tool would you use to grip and bend wire? (a) a spirit level (b) pliers (c) a tape measure (d) a hand drill
16. 16.Which job is sandpaper for? (a) grip and bend wire (b) drive in a nail (c) measure a long length (d) smooth a rough edge
17. 17.🔧 Which tool would you use to turn a screw? (a) pliers (b) a protractor (c) a screwdriver (d) a spanner
18. 18.Which job is a spanner for? (a) tighten a nut (b) cut a wooden plank (c) turn a screw (d) measure a long length
19. 19.🔍 Which is the odd one out? (a) cut towards your hand (b) put tools back after use (c) touch a hot glue tip (d) leave tools on the floor
20. 20.True or false: to wear safety goggles is not safe. (a) False (b) True
21. 21.🔍 Which is the odd one out? (a) cut away from your body (b) let adults use hot glue (c) wear safety goggles (d) leave tools on the floor
22. 22.True or false: to leave tools on the floor is not safe. (a) False (b) True
23. 23.🦺 In the workshop, is it safe to wear safety goggles? (a) safe (b) not safe
24. 24.True or false: to measure a long length, use pliers. (a) True (b) False
25. 25.🦺 How should you carry scissors? (a) by the blades (b) while running (c) points up, open (d) points down, closed
26. 26.True or false: to make a hole in wood, use a hand drill. (a) False (b) True
27. 27.🦺 In the workshop, is it safe to put tools back after use? (a) safe (b) not safe
28. 28.🔍 Which is the odd one out? (a) use a cracked tool (b) let adults use hot glue (c) cut towards your hand (d) play near a moving drill
29. 29.🔧 Which tool would you use to measure a long length? (a) a spirit level (b) a tape measure (c) pliers (d) a protractor
30. 30.Which job is a spirit level for? (a) measure an angle (b) cut a wooden plank (c) turn a screw (d) check a shelf is level
31. 31.True or false: to leave tools on the floor is safe. (a) False (b) True
32. 32.True or false: to cut a wooden plank, use a saw. (a) True (b) False
33. 33.Which job is a hand drill for? (a) make a hole in wood (b) cut a wooden plank (c) measure an angle (d) turn a screw
34. 34.True or false: to grip and bend wire, use pliers. (a) True (b) False
35. 35.True or false: to cut a wooden plank, use a tape measure. (a) True (b) False
36. 36.True or false: to clamp wood before sawing is not safe. (a) True (b) False
37. 37.True or false: to touch a hot glue tip is safe. (a) False (b) True
38. 38.True or false: to cut away from your body is not safe. (a) False (b) True
39. 39.True or false: to tighten a nut, use a screwdriver. (a) True (b) False
40. 40.Which job is a hammer for? (a) cut a wooden plank (b) turn a screw (c) check a shelf is level (d) drive in a nail

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids