Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 153 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) the youngest child (c) a stranger (d) an adult
2. 2.Which job is a protractor for? (a) measure an angle (b) check a shelf is level (c) measure a long length (d) smooth a rough edge
3. 3.🦺 In the workshop, is it safe to touch a hot glue tip? (a) not safe (b) safe
4. 4.Which job is a spanner for? (a) turn a screw (b) check a shelf is level (c) tighten a nut (d) drive in a nail
5. 5.🦺 In the workshop, is it safe to tie back long hair? (a) not safe (b) safe
6. 6.True or false: to drive in a nail, use a hammer. (a) False (b) True
7. 7.True or false: to smooth a rough edge, use sandpaper. (a) False (b) True
8. 8.🔍 Which is the odd one out? (a) let adults use hot glue (b) leave tools on the floor (c) wear safety goggles (d) tie back long hair
9. 9.Which job is a hand drill for? (a) make a hole in wood (b) measure a long length (c) grip and bend wire (d) measure an angle
10. 10.🔍 Which is the odd one out? (a) leave tools on the floor (b) cut towards your hand (c) use a cracked tool (d) wear safety goggles
11. 11.🦺 In the workshop, is it safe to let adults use hot glue? (a) not safe (b) safe
12. 12.🔍 Which is the odd one out? (a) put tools back after use (b) wear safety goggles (c) let adults use hot glue (d) use a cracked tool
13. 13.🔧 Which tool would you use to make a hole in wood? (a) a hammer (b) a spanner (c) a hand drill (d) a spirit level
14. 14.Which job is a spirit level for? (a) cut a wooden plank (b) check a shelf is level (c) smooth a rough edge (d) turn a screw
15. 15.Which job is sandpaper for? (a) check a shelf is level (b) smooth a rough edge (c) grip and bend wire (d) make a hole in wood
16. 16.True or false: to let adults use hot glue is not safe. (a) False (b) True
17. 17.🦺 In the workshop, is it safe to clamp wood before sawing? (a) safe (b) not safe
18. 18.Which job is a saw for? (a) cut a wooden plank (b) measure a long length (c) drive in a nail (d) measure an angle
19. 19.True or false: to measure an angle, use a protractor. (a) False (b) True
20. 20.🔍 Which is the odd one out? (a) cut towards your hand (b) run while holding tools (c) let adults use hot glue (d) leave tools on the floor
21. 21.🔧 Which tool would you use to measure an angle? (a) a spanner (b) sandpaper (c) a protractor (d) a tape measure
22. 22.🔧 Which tool would you use to check a shelf is level? (a) a saw (b) a protractor (c) a screwdriver (d) a spirit level
23. 23.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
24. 24.🔧 Which tool would you use to turn a screw? (a) a protractor (b) a screwdriver (c) a tape measure (d) a spirit level
25. 25.True or false: to carry scissors closed is not safe. (a) True (b) False
26. 26.True or false: to clamp wood before sawing is not safe. (a) False (b) True
27. 27.Which job is a hammer for? (a) turn a screw (b) cut a wooden plank (c) drive in a nail (d) smooth a rough edge
28. 28.🔧 Which tool would you use to smooth a rough edge? (a) a protractor (b) a spanner (c) a saw (d) sandpaper
29. 29.Which job is a screwdriver for? (a) turn a screw (b) smooth a rough edge (c) cut a wooden plank (d) measure a long length
30. 30.🔍 Which is the odd one out? (a) play near a moving drill (b) use a cracked tool (c) carry scissors closed (d) touch a hot glue tip
31. 31.True or false: to run while holding tools is not safe. (a) False (b) True
32. 32.🔧 Which tool would you use to cut a wooden plank? (a) a tape measure (b) a saw (c) sandpaper (d) a hammer
33. 33.True or false: to cut a wooden plank, use a tape measure. (a) True (b) False
34. 34.🔧 Which tool would you use to measure a long length? (a) a hammer (b) a tape measure (c) a spanner (d) a screwdriver
35. 35.True or false: to tighten a nut, use a hammer. (a) True (b) False
36. 36.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
37. 37.🦺 How should you carry scissors? (a) points up, open (b) while running (c) points down, closed (d) by the blades
38. 38.True or false: to drive in a nail, use a screwdriver. (a) False (b) True
39. 39.🔍 Which is the odd one out? (a) carry scissors closed (b) play near a moving drill (c) wear safety goggles (d) put tools back after use
40. 40.True or false: to touch a hot glue tip is not safe. (a) True (b) False

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids