← Tools and workshop safety lesson New set →

Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 174 · 40 questions
TalentJR

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

NameDateTime takenScore ___ / 40
  1. 1.🦺 How should you carry scissors? (a) by the blades (b) points up, open (c) while running (d) points down, closed
  2. 2.Which job is a tape measure for? (a) check a shelf is level (b) cut a wooden plank (c) make a hole in wood (d) measure a long length
  3. 3.🔧 Which tool would you use to grip and bend wire? (a) a spirit level (b) sandpaper (c) pliers (d) a spanner
  4. 4.🔍 Which is the odd one out? (a) cut towards your hand (b) play near a moving drill (c) run while holding tools (d) put tools back after use
  5. 5.Which job is a spirit level for? (a) measure an angle (b) make a hole in wood (c) cut a wooden plank (d) check a shelf is level
  6. 6.True or false: to run while holding tools is not safe. (a) False (b) True
  7. 7.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
  8. 8.True or false: to let adults use hot glue is safe. (a) False (b) True
  9. 9.Which job is a saw for? (a) cut a wooden plank (b) smooth a rough edge (c) tighten a nut (d) measure an angle
  10. 10.True or false: to cut a wooden plank, use a saw. (a) False (b) True
  11. 11.True or false: to measure an angle, use sandpaper. (a) False (b) True
  12. 12.Which job is a hand drill for? (a) turn a screw (b) smooth a rough edge (c) make a hole in wood (d) cut a wooden plank
  13. 13.🔍 Which is the odd one out? (a) put tools back after use (b) clamp wood before sawing (c) let adults use hot glue (d) cut towards your hand
  14. 14.True or false: to play near a moving drill is safe. (a) False (b) True
  15. 15.Which job is pliers for? (a) drive in a nail (b) grip and bend wire (c) turn a screw (d) cut a wooden plank
  16. 16.True or false: to tighten a nut, use a spanner. (a) False (b) True
  17. 17.🦺 In the workshop, is it safe to tie back long hair? (a) safe (b) not safe
  18. 18.🔍 Which is the odd one out? (a) clamp wood before sawing (b) play near a moving drill (c) leave tools on the floor (d) touch a hot glue tip
  19. 19.True or false: to cut a wooden plank, use sandpaper. (a) True (b) False
  20. 20.Which job is a spanner for? (a) tighten a nut (b) cut a wooden plank (c) drive in a nail (d) measure an angle
  21. 21.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) a cap (c) nothing (d) sunglasses
  22. 22.True or false: to touch a hot glue tip is safe. (a) True (b) False
  23. 23.True or false: to measure a long length, use a hammer. (a) True (b) False
  24. 24.True or false: to measure a long length, use a tape measure. (a) False (b) True
  25. 25.🦺 In the workshop, is it safe to clamp wood before sawing? (a) not safe (b) safe
  26. 26.True or false: to measure a long length, use a saw. (a) True (b) False
  27. 27.Which job is a hammer for? (a) cut a wooden plank (b) measure a long length (c) drive in a nail (d) make a hole in wood
  28. 28.🔍 Which is the odd one out? (a) tie back long hair (b) carry scissors closed (c) play near a moving drill (d) cut away from your body
  29. 29.🔍 Which is the odd one out? (a) touch a hot glue tip (b) leave tools on the floor (c) play near a moving drill (d) wear safety goggles
  30. 30.🔍 Which is the odd one out? (a) tie back long hair (b) wear safety goggles (c) leave tools on the floor (d) cut away from your body
  31. 31.🔧 Which tool would you use to measure a long length? (a) a hand drill (b) a tape measure (c) sandpaper (d) a screwdriver
  32. 32.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) an adult (b) any child alone (c) the youngest child (d) a stranger
  33. 33.True or false: to check a shelf is level, use a spirit level. (a) False (b) True
  34. 34.True or false: to turn a screw, use a screwdriver. (a) False (b) True
  35. 35.True or false: to let adults use hot glue is not safe. (a) True (b) False
  36. 36.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe
  37. 37.🦺 In the workshop, is it safe to leave tools on the floor? (a) safe (b) not safe
  38. 38.🔧 Which tool would you use to drive in a nail? (a) pliers (b) sandpaper (c) a hammer (d) a hand drill
  39. 39.🦺 In the workshop, is it safe to let adults use hot glue? (a) safe (b) not safe
  40. 40.🔧 Which tool would you use to measure an angle? (a) a saw (b) a hand drill (c) a protractor (d) a screwdriver

Answer key

  1. points down, closed
  2. measure a long length
  3. pliers
  4. put tools back after use
  5. check a shelf is level
  6. True
  7. safe
  8. True
  9. cut a wooden plank
  10. True
  11. False
  12. make a hole in wood
  13. cut towards your hand
  14. False
  15. grip and bend wire
  16. True
  17. safe
  18. clamp wood before sawing
  19. False
  20. tighten a nut
  21. safety goggles
  22. False
  23. False
  24. True
  25. safe
  26. False
  27. drive in a nail
  28. play near a moving drill
  29. wear safety goggles
  30. leave tools on the floor
  31. a tape measure
  32. an adult
  33. True
  34. True
  35. False
  36. not safe
  37. not safe
  38. a hammer
  39. safe
  40. a protractor

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids