Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 195 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🔧 Which tool would you use to check a shelf is level? (a) pliers (b) a protractor (c) a spirit level (d) a hammer
2. 2.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) a cap (c) safety goggles (d) nothing
3. 3.🔍 Which is the odd one out? (a) wear safety goggles (b) put tools back after use (c) touch a hot glue tip (d) cut away from your body
4. 4.True or false: to put tools back after use is safe. (a) True (b) False
5. 5.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
6. 6.True or false: to run while holding tools is safe. (a) True (b) False
7. 7.True or false: to wear safety goggles is safe. (a) False (b) True
8. 8.True or false: to check a shelf is level, use a spirit level. (a) True (b) False
9. 9.Which job is a hammer for? (a) drive in a nail (b) cut a wooden plank (c) turn a screw (d) check a shelf is level
10. 10.True or false: to cut a wooden plank, use a spanner. (a) True (b) False
11. 11.Which job is a protractor for? (a) make a hole in wood (b) drive in a nail (c) measure an angle (d) turn a screw
12. 12.Which job is pliers for? (a) measure a long length (b) smooth a rough edge (c) check a shelf is level (d) grip and bend wire
13. 13.🦺 In the workshop, is it safe to cut away from your body? (a) not safe (b) safe
14. 14.🔧 Which tool would you use to tighten a nut? (a) a spanner (b) a saw (c) a tape measure (d) a spirit level
15. 15.🔧 Which tool would you use to measure a long length? (a) a spirit level (b) a hand drill (c) a saw (d) a tape measure
16. 16.Which job is a spanner for? (a) check a shelf is level (b) drive in a nail (c) measure a long length (d) tighten a nut
17. 17.🦺 In the workshop, is it safe to clamp wood before sawing? (a) safe (b) not safe
18. 18.🔍 Which is the odd one out? (a) put tools back after use (b) clamp wood before sawing (c) run while holding tools (d) wear safety goggles
19. 19.🦺 How should you carry scissors? (a) points down, closed (b) while running (c) by the blades (d) points up, open
20. 20.🦺 In the workshop, is it safe to let adults use hot glue? (a) safe (b) not safe
21. 21.True or false: to smooth a rough edge, use a protractor. (a) True (b) False
22. 22.Which job is a screwdriver for? (a) measure a long length (b) smooth a rough edge (c) grip and bend wire (d) turn a screw
23. 23.True or false: to put tools back after use is not safe. (a) True (b) False
24. 24.🔧 Which tool would you use to drive in a nail? (a) a hand drill (b) a protractor (c) a hammer (d) pliers
25. 25.True or false: to wear safety goggles is not safe. (a) False (b) True
26. 26.🔧 Which tool would you use to measure an angle? (a) a saw (b) a tape measure (c) a hand drill (d) a protractor
27. 27.🔧 Which tool would you use to turn a screw? (a) a spirit level (b) pliers (c) a screwdriver (d) a tape measure
28. 28.Which job is a hand drill for? (a) grip and bend wire (b) measure a long length (c) check a shelf is level (d) make a hole in wood
29. 29.True or false: to cut a wooden plank, use a hammer. (a) True (b) False
30. 30.True or false: to tighten a nut, use a tape measure. (a) False (b) True
31. 31.🔧 Which tool would you use to smooth a rough edge? (a) a screwdriver (b) a spirit level (c) a spanner (d) sandpaper
32. 32.🔍 Which is the odd one out? (a) touch a hot glue tip (b) tie back long hair (c) run while holding tools (d) play near a moving drill
33. 33.🔍 Which is the odd one out? (a) play near a moving drill (b) leave tools on the floor (c) touch a hot glue tip (d) cut away from your body
34. 34.🔍 Which is the odd one out? (a) wear safety goggles (b) use a cracked tool (c) let adults use hot glue (d) put tools back after use
35. 35.True or false: to tighten a nut, use a spanner. (a) True (b) False
36. 36.🔍 Which is the odd one out? (a) run while holding tools (b) touch a hot glue tip (c) clamp wood before sawing (d) cut towards your hand
37. 37.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) the youngest child (b) a stranger (c) any child alone (d) an adult
38. 38.True or false: to check a shelf is level, use a screwdriver. (a) False (b) True
39. 39.True or false: to cut away from your body is not safe. (a) True (b) False
40. 40.True or false: to leave tools on the floor is safe. (a) False (b) True

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids