Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 197 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.Which job is a saw for? (a) make a hole in wood (b) cut a wooden plank (c) drive in a nail (d) tighten a nut
2. 2.🔍 Which is the odd one out? (a) touch a hot glue tip (b) put tools back after use (c) leave tools on the floor (d) play near a moving drill
3. 3.🦺 In the workshop, is it safe to use a cracked tool? (a) not safe (b) safe
4. 4.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) a cap (c) nothing (d) safety goggles
5. 5.🦺 How should you carry scissors? (a) points up, open (b) by the blades (c) while running (d) points down, closed
6. 6.🔧 Which tool would you use to measure a long length? (a) a hand drill (b) a hammer (c) a spanner (d) a tape measure
7. 7.True or false: to measure a long length, use a spirit level. (a) False (b) True
8. 8.🦺 In the workshop, is it safe to tie back long hair? (a) not safe (b) safe
9. 9.True or false: to turn a screw, use pliers. (a) False (b) True
10. 10.Which job is a spanner for? (a) make a hole in wood (b) tighten a nut (c) drive in a nail (d) grip and bend wire
11. 11.🔍 Which is the odd one out? (a) touch a hot glue tip (b) play near a moving drill (c) leave tools on the floor (d) carry scissors closed
12. 12.🔧 Which tool would you use to measure an angle? (a) sandpaper (b) a saw (c) a hammer (d) a protractor
13. 13.🔍 Which is the odd one out? (a) tie back long hair (b) carry scissors closed (c) clamp wood before sawing (d) touch a hot glue tip
14. 14.True or false: to run while holding tools is safe. (a) True (b) False
15. 15.Which job is a protractor for? (a) check a shelf is level (b) drive in a nail (c) measure an angle (d) make a hole in wood
16. 16.Which job is a screwdriver for? (a) grip and bend wire (b) drive in a nail (c) check a shelf is level (d) turn a screw
17. 17.🦺 In the workshop, is it safe to run while holding tools? (a) safe (b) not safe
18. 18.True or false: to touch a hot glue tip is safe. (a) True (b) False
19. 19.True or false: to measure an angle, use a protractor. (a) False (b) True
20. 20.Which job is pliers for? (a) measure a long length (b) tighten a nut (c) smooth a rough edge (d) grip and bend wire
21. 21.Which job is sandpaper for? (a) measure an angle (b) make a hole in wood (c) smooth a rough edge (d) grip and bend wire
22. 22.🔧 Which tool would you use to grip and bend wire? (a) a screwdriver (b) a protractor (c) a saw (d) pliers
23. 23.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
24. 24.True or false: to carry scissors closed is safe. (a) False (b) True
25. 25.Which job is a tape measure for? (a) cut a wooden plank (b) turn a screw (c) check a shelf is level (d) measure a long length
26. 26.True or false: to turn a screw, use a screwdriver. (a) False (b) True
27. 27.True or false: to tighten a nut, use a spanner. (a) False (b) True
28. 28.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
29. 29.True or false: to make a hole in wood, use a hammer. (a) False (b) True
30. 30.🔍 Which is the odd one out? (a) tie back long hair (b) leave tools on the floor (c) carry scissors closed (d) clamp wood before sawing
31. 31.🦺 In the workshop, is it safe to leave tools on the floor? (a) safe (b) not safe
32. 32.True or false: to clamp wood before sawing is not safe. (a) False (b) True
33. 33.🔧 Which tool would you use to cut a wooden plank? (a) a tape measure (b) pliers (c) a hammer (d) a saw
34. 34.True or false: to measure a long length, use a tape measure. (a) True (b) False
35. 35.🔧 Which tool would you use to tighten a nut? (a) a protractor (b) a tape measure (c) a hand drill (d) a spanner
36. 36.🔍 Which is the odd one out? (a) play near a moving drill (b) wear safety goggles (c) touch a hot glue tip (d) run while holding tools
37. 37.True or false: to turn a screw, use a saw. (a) True (b) False
38. 38.🦺 In the workshop, is it safe to let adults use hot glue? (a) not safe (b) safe
39. 39.True or false: to cut a wooden plank, use a hand drill. (a) True (b) False
40. 40.True or false: to turn a screw, use a tape measure. (a) True (b) False

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids