← Tools and workshop safety lesson New set →

Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 201 · 40 questions
TalentJR

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

NameDateTime takenScore ___ / 40
  1. 1.Which job is sandpaper for? (a) smooth a rough edge (b) drive in a nail (c) grip and bend wire (d) cut a wooden plank
  2. 2.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
  3. 3.True or false: to measure a long length, use a protractor. (a) False (b) True
  4. 4.Which job is a hand drill for? (a) grip and bend wire (b) make a hole in wood (c) turn a screw (d) tighten a nut
  5. 5.True or false: to measure a long length, use a hand drill. (a) True (b) False
  6. 6.🔍 Which is the odd one out? (a) run while holding tools (b) cut towards your hand (c) play near a moving drill (d) tie back long hair
  7. 7.True or false: to grip and bend wire, use a hand drill. (a) False (b) True
  8. 8.True or false: to cut away from your body is not safe. (a) False (b) True
  9. 9.🔧 Which tool would you use to smooth a rough edge? (a) a spirit level (b) sandpaper (c) a hand drill (d) a tape measure
  10. 10.🦺 How should you carry scissors? (a) points up, open (b) while running (c) points down, closed (d) by the blades
  11. 11.Which job is a tape measure for? (a) grip and bend wire (b) measure an angle (c) measure a long length (d) check a shelf is level
  12. 12.True or false: to grip and bend wire, use pliers. (a) False (b) True
  13. 13.True or false: to wear safety goggles is safe. (a) True (b) False
  14. 14.True or false: to touch a hot glue tip is safe. (a) True (b) False
  15. 15.True or false: to smooth a rough edge, use sandpaper. (a) True (b) False
  16. 16.🔍 Which is the odd one out? (a) use a cracked tool (b) play near a moving drill (c) leave tools on the floor (d) put tools back after use
  17. 17.🔍 Which is the odd one out? (a) touch a hot glue tip (b) run while holding tools (c) clamp wood before sawing (d) cut towards your hand
  18. 18.True or false: to put tools back after use is safe. (a) False (b) True
  19. 19.Which job is a spirit level for? (a) make a hole in wood (b) turn a screw (c) check a shelf is level (d) measure a long length
  20. 20.Which job is a protractor for? (a) turn a screw (b) drive in a nail (c) measure a long length (d) measure an angle
  21. 21.True or false: to tighten a nut, use a saw. (a) True (b) False
  22. 22.🦺 In the workshop, is it safe to clamp wood before sawing? (a) not safe (b) safe
  23. 23.🔧 Which tool would you use to drive in a nail? (a) a hammer (b) a protractor (c) a spirit level (d) pliers
  24. 24.🔍 Which is the odd one out? (a) clamp wood before sawing (b) cut towards your hand (c) wear safety goggles (d) carry scissors closed
  25. 25.True or false: to run while holding tools is safe. (a) False (b) True
  26. 26.True or false: to smooth a rough edge, use a spirit level. (a) False (b) True
  27. 27.Which job is a saw for? (a) make a hole in wood (b) measure an angle (c) turn a screw (d) cut a wooden plank
  28. 28.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) a stranger (b) an adult (c) any child alone (d) the youngest child
  29. 29.🦺 What protects your eyes when sawing or drilling? (a) a cap (b) nothing (c) safety goggles (d) sunglasses
  30. 30.Which job is a hammer for? (a) measure a long length (b) make a hole in wood (c) drive in a nail (d) check a shelf is level
  31. 31.🔧 Which tool would you use to turn a screw? (a) a protractor (b) a screwdriver (c) a hand drill (d) a tape measure
  32. 32.🔧 Which tool would you use to measure a long length? (a) a screwdriver (b) pliers (c) a hand drill (d) a tape measure
  33. 33.True or false: to play near a moving drill is safe. (a) False (b) True
  34. 34.Which job is a screwdriver for? (a) turn a screw (b) make a hole in wood (c) check a shelf is level (d) tighten a nut
  35. 35.True or false: to leave tools on the floor is not safe. (a) True (b) False
  36. 36.True or false: to carry scissors closed is safe. (a) False (b) True
  37. 37.True or false: to cut towards your hand is safe. (a) False (b) True
  38. 38.🔧 Which tool would you use to measure an angle? (a) a protractor (b) a tape measure (c) a hammer (d) a spirit level
  39. 39.True or false: to drive in a nail, use sandpaper. (a) True (b) False
  40. 40.🦺 In the workshop, is it safe to cut away from your body? (a) not safe (b) safe

Answer key

  1. smooth a rough edge
  2. not safe
  3. False
  4. make a hole in wood
  5. False
  6. tie back long hair
  7. False
  8. False
  9. sandpaper
  10. points down, closed
  11. measure a long length
  12. True
  13. True
  14. False
  15. True
  16. put tools back after use
  17. clamp wood before sawing
  18. True
  19. check a shelf is level
  20. measure an angle
  21. False
  22. safe
  23. a hammer
  24. cut towards your hand
  25. False
  26. False
  27. cut a wooden plank
  28. an adult
  29. safety goggles
  30. drive in a nail
  31. a screwdriver
  32. a tape measure
  33. False
  34. turn a screw
  35. True
  36. True
  37. False
  38. a protractor
  39. False
  40. safe

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids