Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 204 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🔧 Which tool would you use to turn a screw? (a) a screwdriver (b) a tape measure (c) a hammer (d) a spanner
2. 2.🦺 In the workshop, is it safe to clamp wood before sawing? (a) not safe (b) safe
3. 3.True or false: to wear safety goggles is not safe. (a) True (b) False
4. 4.True or false: to cut a wooden plank, use a tape measure. (a) False (b) True
5. 5.🔧 Which tool would you use to measure an angle? (a) a saw (b) a spanner (c) a protractor (d) sandpaper
6. 6.🔧 Which tool would you use to make a hole in wood? (a) a spirit level (b) pliers (c) a hand drill (d) a tape measure
7. 7.True or false: to cut towards your hand is safe. (a) True (b) False
8. 8.🦺 In the workshop, is it safe to leave tools on the floor? (a) safe (b) not safe
9. 9.🦺 How should you carry scissors? (a) points up, open (b) while running (c) points down, closed (d) by the blades
10. 10.🔧 Which tool would you use to smooth a rough edge? (a) a spirit level (b) a tape measure (c) a protractor (d) sandpaper
11. 11.Which job is a spirit level for? (a) smooth a rough edge (b) cut a wooden plank (c) measure a long length (d) check a shelf is level
12. 12.True or false: to carry scissors closed is not safe. (a) False (b) True
13. 13.True or false: to check a shelf is level, use a spirit level. (a) True (b) False
14. 14.Which job is pliers for? (a) measure a long length (b) measure an angle (c) grip and bend wire (d) smooth a rough edge
15. 15.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) nothing (c) sunglasses (d) a cap
16. 16.True or false: to leave tools on the floor is not safe. (a) False (b) True
17. 17.🔍 Which is the odd one out? (a) wear safety goggles (b) cut away from your body (c) carry scissors closed (d) use a cracked tool
18. 18.🦺 In the workshop, is it safe to carry scissors closed? (a) not safe (b) safe
19. 19.True or false: to put tools back after use is not safe. (a) True (b) False
20. 20.🔍 Which is the odd one out? (a) wear safety goggles (b) tie back long hair (c) put tools back after use (d) leave tools on the floor
21. 21.🔧 Which tool would you use to grip and bend wire? (a) a tape measure (b) pliers (c) a protractor (d) a hammer
22. 22.🔧 Which tool would you use to measure a long length? (a) a spirit level (b) a tape measure (c) a hand drill (d) a spanner
23. 23.🔍 Which is the odd one out? (a) carry scissors closed (b) wear safety goggles (c) play near a moving drill (d) cut away from your body
24. 24.🔧 Which tool would you use to check a shelf is level? (a) a tape measure (b) sandpaper (c) a spanner (d) a spirit level
25. 25.🔧 Which tool would you use to drive in a nail? (a) a protractor (b) a screwdriver (c) a hammer (d) a spirit level
26. 26.🦺 In the workshop, is it safe to cut towards your hand? (a) not safe (b) safe
27. 27.🔍 Which is the odd one out? (a) tie back long hair (b) cut towards your hand (c) put tools back after use (d) wear safety goggles
28. 28.True or false: to tie back long hair is safe. (a) True (b) False
29. 29.Which job is a saw for? (a) cut a wooden plank (b) measure an angle (c) turn a screw (d) check a shelf is level
30. 30.Which job is a tape measure for? (a) turn a screw (b) measure a long length (c) measure an angle (d) make a hole in wood
31. 31.True or false: to turn a screw, use a spanner. (a) False (b) True
32. 32.🔍 Which is the odd one out? (a) run while holding tools (b) touch a hot glue tip (c) play near a moving drill (d) wear safety goggles
33. 33.True or false: to measure a long length, use a screwdriver. (a) True (b) False
34. 34.True or false: to check a shelf is level, use a hand drill. (a) False (b) True
35. 35.True or false: to measure a long length, use a spirit level. (a) True (b) False
36. 36.Which job is a spanner for? (a) drive in a nail (b) cut a wooden plank (c) tighten a nut (d) check a shelf is level
37. 37.🔍 Which is the odd one out? (a) touch a hot glue tip (b) put tools back after use (c) leave tools on the floor (d) play near a moving drill
38. 38.True or false: to clamp wood before sawing is not safe. (a) False (b) True
39. 39.True or false: to tighten a nut, use a protractor. (a) False (b) True
40. 40.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) the youngest child (c) a stranger (d) an adult

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids