Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 209 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🔧 Which tool would you use to check a shelf is level? (a) a tape measure (b) a screwdriver (c) a spirit level (d) a hammer
2. 2.🦺 In the workshop, is it safe to carry scissors closed? (a) safe (b) not safe
3. 3.🔧 Which tool would you use to drive in a nail? (a) a screwdriver (b) a hammer (c) a protractor (d) a spanner
4. 4.True or false: to carry scissors closed is not safe. (a) True (b) False
5. 5.True or false: to wear safety goggles is safe. (a) True (b) False
6. 6.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) a cap (c) safety goggles (d) nothing
7. 7.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe
8. 8.True or false: to cut towards your hand is safe. (a) True (b) False
9. 9.🦺 In the workshop, is it safe to leave tools on the floor? (a) not safe (b) safe
10. 10.🔧 Which tool would you use to smooth a rough edge? (a) sandpaper (b) a screwdriver (c) a hammer (d) a spirit level
11. 11.True or false: to clamp wood before sawing is safe. (a) False (b) True
12. 12.🔍 Which is the odd one out? (a) leave tools on the floor (b) touch a hot glue tip (c) carry scissors closed (d) play near a moving drill
13. 13.🔧 Which tool would you use to tighten a nut? (a) a tape measure (b) a spirit level (c) a spanner (d) pliers
14. 14.🔍 Which is the odd one out? (a) run while holding tools (b) wear safety goggles (c) cut towards your hand (d) leave tools on the floor
15. 15.🔧 Which tool would you use to measure an angle? (a) a protractor (b) a spirit level (c) pliers (d) a hammer
16. 16.Which job is a tape measure for? (a) smooth a rough edge (b) measure a long length (c) make a hole in wood (d) check a shelf is level
17. 17.True or false: to touch a hot glue tip is safe. (a) True (b) False
18. 18.🔧 Which tool would you use to cut a wooden plank? (a) a spanner (b) sandpaper (c) a spirit level (d) a saw
19. 19.Which job is a protractor for? (a) smooth a rough edge (b) check a shelf is level (c) measure an angle (d) turn a screw
20. 20.🦺 How should you carry scissors? (a) by the blades (b) while running (c) points down, closed (d) points up, open
21. 21.🔍 Which is the odd one out? (a) carry scissors closed (b) put tools back after use (c) touch a hot glue tip (d) clamp wood before sawing
22. 22.🔍 Which is the odd one out? (a) cut away from your body (b) carry scissors closed (c) let adults use hot glue (d) run while holding tools
23. 23.🔍 Which is the odd one out? (a) touch a hot glue tip (b) leave tools on the floor (c) play near a moving drill (d) tie back long hair
24. 24.Which job is a spirit level for? (a) cut a wooden plank (b) check a shelf is level (c) drive in a nail (d) measure a long length
25. 25.True or false: to measure an angle, use a spanner. (a) True (b) False
26. 26.Which job is a screwdriver for? (a) turn a screw (b) measure a long length (c) drive in a nail (d) check a shelf is level
27. 27.Which job is a spanner for? (a) measure an angle (b) smooth a rough edge (c) tighten a nut (d) check a shelf is level
28. 28.🔍 Which is the odd one out? (a) clamp wood before sawing (b) cut towards your hand (c) cut away from your body (d) tie back long hair
29. 29.True or false: to let adults use hot glue is not safe. (a) True (b) False
30. 30.🔧 Which tool would you use to turn a screw? (a) a protractor (b) a screwdriver (c) a spanner (d) a hand drill
31. 31.True or false: to measure a long length, use a spanner. (a) True (b) False
32. 32.Which job is a saw for? (a) cut a wooden plank (b) measure a long length (c) measure an angle (d) smooth a rough edge
33. 33.🔧 Which tool would you use to make a hole in wood? (a) a hand drill (b) a screwdriver (c) sandpaper (d) pliers
34. 34.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
35. 35.True or false: to leave tools on the floor is safe. (a) False (b) True
36. 36.🔍 Which is the odd one out? (a) use a cracked tool (b) clamp wood before sawing (c) wear safety goggles (d) carry scissors closed
37. 37.True or false: to run while holding tools is safe. (a) False (b) True
38. 38.Which job is a hammer for? (a) measure a long length (b) tighten a nut (c) drive in a nail (d) smooth a rough edge
39. 39.True or false: to make a hole in wood, use a screwdriver. (a) True (b) False
40. 40.True or false: to drive in a nail, use a hammer. (a) False (b) True

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids