Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 252 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.True or false: to drive in a nail, use sandpaper. (a) False (b) True
2. 2.🔧 Which tool would you use to drive in a nail? (a) a hammer (b) a hand drill (c) a spirit level (d) sandpaper
3. 3.Which job is a hammer for? (a) measure an angle (b) drive in a nail (c) measure a long length (d) tighten a nut
4. 4.🔧 Which tool would you use to measure an angle? (a) a hand drill (b) a tape measure (c) a saw (d) a protractor
5. 5.True or false: to play near a moving drill is not safe. (a) False (b) True
6. 6.🦺 What protects your eyes when sawing or drilling? (a) nothing (b) safety goggles (c) a cap (d) sunglasses
7. 7.True or false: to put tools back after use is not safe. (a) False (b) True
8. 8.🔍 Which is the odd one out? (a) put tools back after use (b) wear safety goggles (c) leave tools on the floor (d) let adults use hot glue
9. 9.True or false: to carry scissors closed is safe. (a) True (b) False
10. 10.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
11. 11.🔍 Which is the odd one out? (a) carry scissors closed (b) put tools back after use (c) wear safety goggles (d) play near a moving drill
12. 12.🔍 Which is the odd one out? (a) wear safety goggles (b) leave tools on the floor (c) cut towards your hand (d) use a cracked tool
13. 13.🔧 Which tool would you use to tighten a nut? (a) a spanner (b) a screwdriver (c) pliers (d) a saw
14. 14.🦺 How should you carry scissors? (a) points up, open (b) while running (c) by the blades (d) points down, closed
15. 15.Which job is sandpaper for? (a) smooth a rough edge (b) grip and bend wire (c) make a hole in wood (d) cut a wooden plank
16. 16.True or false: to check a shelf is level, use a screwdriver. (a) False (b) True
17. 17.🔍 Which is the odd one out? (a) touch a hot glue tip (b) clamp wood before sawing (c) carry scissors closed (d) let adults use hot glue
18. 18.🔍 Which is the odd one out? (a) use a cracked tool (b) tie back long hair (c) touch a hot glue tip (d) run while holding tools
19. 19.Which job is pliers for? (a) measure a long length (b) smooth a rough edge (c) drive in a nail (d) grip and bend wire
20. 20.True or false: to cut away from your body is safe. (a) True (b) False
21. 21.Which job is a spirit level for? (a) tighten a nut (b) check a shelf is level (c) smooth a rough edge (d) drive in a nail
22. 22.🔧 Which tool would you use to grip and bend wire? (a) a hand drill (b) a tape measure (c) pliers (d) a saw
23. 23.True or false: to turn a screw, use a screwdriver. (a) False (b) True
24. 24.🦺 In the workshop, is it safe to clamp wood before sawing? (a) safe (b) not safe
25. 25.🔍 Which is the odd one out? (a) let adults use hot glue (b) carry scissors closed (c) cut towards your hand (d) tie back long hair
26. 26.🔍 Which is the odd one out? (a) let adults use hot glue (b) cut towards your hand (c) use a cracked tool (d) leave tools on the floor
27. 27.True or false: to tighten a nut, use a spanner. (a) False (b) True
28. 28.🦺 In the workshop, is it safe to cut towards your hand? (a) not safe (b) safe
29. 29.🦺 In the workshop, is it safe to let adults use hot glue? (a) safe (b) not safe
30. 30.True or false: to smooth a rough edge, use sandpaper. (a) False (b) True
31. 31.🔧 Which tool would you use to cut a wooden plank? (a) a spirit level (b) a hand drill (c) a saw (d) a tape measure
32. 32.🔧 Which tool would you use to make a hole in wood? (a) a hammer (b) sandpaper (c) a hand drill (d) pliers
33. 33.Which job is a saw for? (a) tighten a nut (b) check a shelf is level (c) measure an angle (d) cut a wooden plank
34. 34.True or false: to play near a moving drill is safe. (a) True (b) False
35. 35.🔧 Which tool would you use to turn a screw? (a) a screwdriver (b) a saw (c) a hammer (d) a spirit level
36. 36.🦺 In the workshop, is it safe to cut away from your body? (a) safe (b) not safe
37. 37.True or false: to measure a long length, use a tape measure. (a) False (b) True
38. 38.🦺 In the workshop, is it safe to touch a hot glue tip? (a) not safe (b) safe
39. 39.Which job is a spanner for? (a) turn a screw (b) grip and bend wire (c) tighten a nut (d) drive in a nail
40. 40.Which job is a tape measure for? (a) turn a screw (b) measure an angle (c) measure a long length (d) cut a wooden plank

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids