Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 258 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.Which job is a tape measure for? (a) measure a long length (b) drive in a nail (c) check a shelf is level (d) tighten a nut
2. 2.🔧 Which tool would you use to check a shelf is level? (a) a spanner (b) a saw (c) a spirit level (d) a protractor
3. 3.True or false: to play near a moving drill is not safe. (a) True (b) False
4. 4.🔍 Which is the odd one out? (a) put tools back after use (b) let adults use hot glue (c) leave tools on the floor (d) tie back long hair
5. 5.🦺 In the workshop, is it safe to use a cracked tool? (a) not safe (b) safe
6. 6.True or false: to measure a long length, use a tape measure. (a) False (b) True
7. 7.🔧 Which tool would you use to smooth a rough edge? (a) a protractor (b) sandpaper (c) a saw (d) a spanner
8. 8.🦺 How should you carry scissors? (a) while running (b) points up, open (c) points down, closed (d) by the blades
9. 9.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
10. 10.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) nothing (c) a cap (d) safety goggles
11. 11.Which job is pliers for? (a) smooth a rough edge (b) grip and bend wire (c) drive in a nail (d) measure a long length
12. 12.Which job is a saw for? (a) measure an angle (b) make a hole in wood (c) measure a long length (d) cut a wooden plank
13. 13.🔍 Which is the odd one out? (a) tie back long hair (b) wear safety goggles (c) clamp wood before sawing (d) cut towards your hand
14. 14.Which job is a screwdriver for? (a) check a shelf is level (b) turn a screw (c) tighten a nut (d) make a hole in wood
15. 15.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) a stranger (c) the youngest child (d) an adult
16. 16.True or false: to turn a screw, use a hammer. (a) True (b) False
17. 17.True or false: to check a shelf is level, use a spirit level. (a) False (b) True
18. 18.Which job is sandpaper for? (a) measure an angle (b) cut a wooden plank (c) smooth a rough edge (d) drive in a nail
19. 19.True or false: to clamp wood before sawing is not safe. (a) True (b) False
20. 20.True or false: to tie back long hair is safe. (a) True (b) False
21. 21.🔧 Which tool would you use to measure an angle? (a) a saw (b) pliers (c) a spirit level (d) a protractor
22. 22.True or false: to cut away from your body is safe. (a) False (b) True
23. 23.🔧 Which tool would you use to grip and bend wire? (a) a screwdriver (b) a protractor (c) pliers (d) sandpaper
24. 24.True or false: to wear safety goggles is not safe. (a) True (b) False
25. 25.True or false: to check a shelf is level, use a protractor. (a) False (b) True
26. 26.🦺 In the workshop, is it safe to let adults use hot glue? (a) not safe (b) safe
27. 27.True or false: to drive in a nail, use a hammer. (a) True (b) False
28. 28.🦺 In the workshop, is it safe to cut away from your body? (a) safe (b) not safe
29. 29.🔍 Which is the odd one out? (a) wear safety goggles (b) let adults use hot glue (c) carry scissors closed (d) run while holding tools
30. 30.🦺 In the workshop, is it safe to cut towards your hand? (a) safe (b) not safe
31. 31.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
32. 32.True or false: to leave tools on the floor is not safe. (a) False (b) True
33. 33.Which job is a spanner for? (a) tighten a nut (b) grip and bend wire (c) check a shelf is level (d) cut a wooden plank
34. 34.True or false: to let adults use hot glue is safe. (a) True (b) False
35. 35.🦺 In the workshop, is it safe to clamp wood before sawing? (a) safe (b) not safe
36. 36.Which job is a hammer for? (a) turn a screw (b) make a hole in wood (c) drive in a nail (d) tighten a nut
37. 37.🔍 Which is the odd one out? (a) play near a moving drill (b) cut towards your hand (c) wear safety goggles (d) leave tools on the floor
38. 38.🔍 Which is the odd one out? (a) cut towards your hand (b) clamp wood before sawing (c) touch a hot glue tip (d) leave tools on the floor
39. 39.True or false: to put tools back after use is safe. (a) False (b) True
40. 40.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids