Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 260 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🦺 In the workshop, is it safe to clamp wood before sawing? (a) not safe (b) safe
2. 2.True or false: to run while holding tools is safe. (a) True (b) False
3. 3.🔧 Which tool would you use to make a hole in wood? (a) sandpaper (b) a tape measure (c) a spirit level (d) a hand drill
4. 4.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) a cap (c) nothing (d) sunglasses
5. 5.🔧 Which tool would you use to measure an angle? (a) a spanner (b) a screwdriver (c) a saw (d) a protractor
6. 6.🔍 Which is the odd one out? (a) cut away from your body (b) clamp wood before sawing (c) tie back long hair (d) use a cracked tool
7. 7.Which job is a hammer for? (a) turn a screw (b) measure an angle (c) drive in a nail (d) cut a wooden plank
8. 8.True or false: to cut towards your hand is not safe. (a) True (b) False
9. 9.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
10. 10.Which job is a tape measure for? (a) smooth a rough edge (b) turn a screw (c) grip and bend wire (d) measure a long length
11. 11.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) a stranger (b) any child alone (c) the youngest child (d) an adult
12. 12.🔍 Which is the odd one out? (a) leave tools on the floor (b) run while holding tools (c) use a cracked tool (d) let adults use hot glue
13. 13.🦺 How should you carry scissors? (a) while running (b) points down, closed (c) points up, open (d) by the blades
14. 14.True or false: to drive in a nail, use pliers. (a) True (b) False
15. 15.🔧 Which tool would you use to smooth a rough edge? (a) pliers (b) sandpaper (c) a tape measure (d) a protractor
16. 16.🦺 In the workshop, is it safe to carry scissors closed? (a) safe (b) not safe
17. 17.🔧 Which tool would you use to turn a screw? (a) a tape measure (b) a hand drill (c) a protractor (d) a screwdriver
18. 18.Which job is a protractor for? (a) check a shelf is level (b) drive in a nail (c) measure an angle (d) measure a long length
19. 19.Which job is pliers for? (a) tighten a nut (b) check a shelf is level (c) grip and bend wire (d) measure an angle
20. 20.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
21. 21.True or false: to tighten a nut, use a spanner. (a) False (b) True
22. 22.🔍 Which is the odd one out? (a) cut away from your body (b) play near a moving drill (c) carry scissors closed (d) tie back long hair
23. 23.🔍 Which is the odd one out? (a) use a cracked tool (b) leave tools on the floor (c) run while holding tools (d) cut away from your body
24. 24.🔍 Which is the odd one out? (a) play near a moving drill (b) touch a hot glue tip (c) tie back long hair (d) run while holding tools
25. 25.True or false: to use a cracked tool is safe. (a) False (b) True
26. 26.Which job is a spirit level for? (a) grip and bend wire (b) cut a wooden plank (c) check a shelf is level (d) tighten a nut
27. 27.🦺 In the workshop, is it safe to tie back long hair? (a) safe (b) not safe
28. 28.🔧 Which tool would you use to tighten a nut? (a) pliers (b) a saw (c) a spanner (d) a hammer
29. 29.True or false: to tighten a nut, use a screwdriver. (a) False (b) True
30. 30.🔍 Which is the odd one out? (a) touch a hot glue tip (b) leave tools on the floor (c) cut towards your hand (d) wear safety goggles
31. 31.🔧 Which tool would you use to check a shelf is level? (a) a hammer (b) a tape measure (c) a spirit level (d) a saw
32. 32.Which job is a saw for? (a) cut a wooden plank (b) grip and bend wire (c) smooth a rough edge (d) check a shelf is level
33. 33.True or false: to grip and bend wire, use a screwdriver. (a) False (b) True
34. 34.🔍 Which is the odd one out? (a) wear safety goggles (b) put tools back after use (c) tie back long hair (d) leave tools on the floor
35. 35.True or false: to cut a wooden plank, use a saw. (a) False (b) True
36. 36.🔍 Which is the odd one out? (a) clamp wood before sawing (b) cut towards your hand (c) wear safety goggles (d) carry scissors closed
37. 37.Which job is sandpaper for? (a) drive in a nail (b) grip and bend wire (c) smooth a rough edge (d) turn a screw
38. 38.🔧 Which tool would you use to measure a long length? (a) a hammer (b) a tape measure (c) a spirit level (d) sandpaper
39. 39.True or false: to put tools back after use is safe. (a) False (b) True
40. 40.True or false: to measure a long length, use pliers. (a) True (b) False

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids