Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 266 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🔧 Which tool would you use to grip and bend wire? (a) a saw (b) pliers (c) sandpaper (d) a spirit level
2. 2.🦺 How should you carry scissors? (a) points up, open (b) while running (c) points down, closed (d) by the blades
3. 3.Which job is a spanner for? (a) make a hole in wood (b) tighten a nut (c) grip and bend wire (d) drive in a nail
4. 4.True or false: to grip and bend wire, use a protractor. (a) False (b) True
5. 5.True or false: to wear safety goggles is safe. (a) False (b) True
6. 6.Which job is a screwdriver for? (a) turn a screw (b) measure an angle (c) make a hole in wood (d) drive in a nail
7. 7.🔧 Which tool would you use to smooth a rough edge? (a) a hammer (b) sandpaper (c) a hand drill (d) a tape measure
8. 8.🔍 Which is the odd one out? (a) wear safety goggles (b) carry scissors closed (c) put tools back after use (d) run while holding tools
9. 9.🔍 Which is the odd one out? (a) run while holding tools (b) let adults use hot glue (c) play near a moving drill (d) touch a hot glue tip
10. 10.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
11. 11.🔧 Which tool would you use to cut a wooden plank? (a) a hammer (b) a screwdriver (c) a saw (d) sandpaper
12. 12.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) the youngest child (c) an adult (d) a stranger
13. 13.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) sunglasses (c) a cap (d) nothing
14. 14.🔍 Which is the odd one out? (a) use a cracked tool (b) touch a hot glue tip (c) cut towards your hand (d) tie back long hair
15. 15.True or false: to grip and bend wire, use pliers. (a) False (b) True
16. 16.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
17. 17.Which job is a protractor for? (a) measure an angle (b) check a shelf is level (c) measure a long length (d) turn a screw
18. 18.Which job is pliers for? (a) check a shelf is level (b) grip and bend wire (c) measure an angle (d) make a hole in wood
19. 19.True or false: to turn a screw, use a screwdriver. (a) True (b) False
20. 20.🦺 In the workshop, is it safe to leave tools on the floor? (a) not safe (b) safe
21. 21.🦺 In the workshop, is it safe to use a cracked tool? (a) safe (b) not safe
22. 22.🔍 Which is the odd one out? (a) leave tools on the floor (b) wear safety goggles (c) cut towards your hand (d) play near a moving drill
23. 23.Which job is sandpaper for? (a) grip and bend wire (b) drive in a nail (c) cut a wooden plank (d) smooth a rough edge
24. 24.🔍 Which is the odd one out? (a) wear safety goggles (b) clamp wood before sawing (c) play near a moving drill (d) put tools back after use
25. 25.True or false: to run while holding tools is not safe. (a) True (b) False
26. 26.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe
27. 27.🔍 Which is the odd one out? (a) cut away from your body (b) play near a moving drill (c) leave tools on the floor (d) touch a hot glue tip
28. 28.🔧 Which tool would you use to tighten a nut? (a) a tape measure (b) a spanner (c) a hammer (d) a protractor
29. 29.🦺 In the workshop, is it safe to cut away from your body? (a) safe (b) not safe
30. 30.True or false: to leave tools on the floor is safe. (a) True (b) False
31. 31.True or false: to let adults use hot glue is safe. (a) False (b) True
32. 32.True or false: to clamp wood before sawing is not safe. (a) False (b) True
33. 33.Which job is a hand drill for? (a) measure a long length (b) grip and bend wire (c) make a hole in wood (d) smooth a rough edge
34. 34.True or false: to measure an angle, use a protractor. (a) True (b) False
35. 35.🔧 Which tool would you use to measure a long length? (a) a spirit level (b) a spanner (c) a tape measure (d) sandpaper
36. 36.🔧 Which tool would you use to check a shelf is level? (a) sandpaper (b) a saw (c) a spirit level (d) a protractor
37. 37.Which job is a tape measure for? (a) cut a wooden plank (b) turn a screw (c) measure a long length (d) tighten a nut
38. 38.🔍 Which is the odd one out? (a) use a cracked tool (b) clamp wood before sawing (c) put tools back after use (d) cut away from your body
39. 39.True or false: to use a cracked tool is safe. (a) False (b) True
40. 40.🔧 Which tool would you use to drive in a nail? (a) a spirit level (b) pliers (c) sandpaper (d) a hammer

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids