Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 289 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🦺 In the workshop, is it safe to clamp wood before sawing? (a) not safe (b) safe
2. 2.Which job is a spirit level for? (a) make a hole in wood (b) smooth a rough edge (c) check a shelf is level (d) grip and bend wire
3. 3.🔧 Which tool would you use to make a hole in wood? (a) a spirit level (b) a hand drill (c) a protractor (d) a spanner
4. 4.True or false: to carry scissors closed is not safe. (a) False (b) True
5. 5.True or false: to clamp wood before sawing is not safe. (a) False (b) True
6. 6.🔧 Which tool would you use to check a shelf is level? (a) a spirit level (b) a hammer (c) a tape measure (d) a spanner
7. 7.🔧 Which tool would you use to measure a long length? (a) a saw (b) a spirit level (c) a protractor (d) a tape measure
8. 8.🔧 Which tool would you use to drive in a nail? (a) a hammer (b) a tape measure (c) a screwdriver (d) a protractor
9. 9.True or false: to turn a screw, use a screwdriver. (a) True (b) False
10. 10.🔍 Which is the odd one out? (a) cut towards your hand (b) tie back long hair (c) run while holding tools (d) touch a hot glue tip
11. 11.🔧 Which tool would you use to measure an angle? (a) pliers (b) a protractor (c) a screwdriver (d) a saw
12. 12.True or false: to leave tools on the floor is safe. (a) True (b) False
13. 13.🔧 Which tool would you use to turn a screw? (a) a hand drill (b) sandpaper (c) a screwdriver (d) pliers
14. 14.🔧 Which tool would you use to tighten a nut? (a) a spanner (b) a screwdriver (c) a protractor (d) a hammer
15. 15.Which job is a screwdriver for? (a) measure a long length (b) grip and bend wire (c) drive in a nail (d) turn a screw
16. 16.True or false: to turn a screw, use a spirit level. (a) True (b) False
17. 17.Which job is pliers for? (a) smooth a rough edge (b) check a shelf is level (c) grip and bend wire (d) measure an angle
18. 18.Which job is a spanner for? (a) measure a long length (b) tighten a nut (c) make a hole in wood (d) smooth a rough edge
19. 19.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
20. 20.True or false: to make a hole in wood, use a hand drill. (a) False (b) True
21. 21.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) sunglasses (c) nothing (d) a cap
22. 22.Which job is a hand drill for? (a) make a hole in wood (b) grip and bend wire (c) smooth a rough edge (d) drive in a nail
23. 23.🔍 Which is the odd one out? (a) wear safety goggles (b) play near a moving drill (c) put tools back after use (d) clamp wood before sawing
24. 24.Which job is a tape measure for? (a) grip and bend wire (b) smooth a rough edge (c) check a shelf is level (d) measure a long length
25. 25.🔍 Which is the odd one out? (a) play near a moving drill (b) use a cracked tool (c) cut towards your hand (d) wear safety goggles
26. 26.True or false: to cut a wooden plank, use a saw. (a) False (b) True
27. 27.True or false: to use a cracked tool is safe. (a) False (b) True
28. 28.🦺 How should you carry scissors? (a) by the blades (b) points down, closed (c) points up, open (d) while running
29. 29.🔍 Which is the odd one out? (a) tie back long hair (b) clamp wood before sawing (c) put tools back after use (d) touch a hot glue tip
30. 30.True or false: to measure a long length, use a tape measure. (a) True (b) False
31. 31.🔍 Which is the odd one out? (a) carry scissors closed (b) cut away from your body (c) cut towards your hand (d) wear safety goggles
32. 32.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe
33. 33.True or false: to grip and bend wire, use a spirit level. (a) False (b) True
34. 34.True or false: to play near a moving drill is safe. (a) True (b) False
35. 35.True or false: to tighten a nut, use a tape measure. (a) False (b) True
36. 36.Which job is a saw for? (a) grip and bend wire (b) drive in a nail (c) cut a wooden plank (d) turn a screw
37. 37.True or false: to drive in a nail, use a hammer. (a) True (b) False
38. 38.True or false: to cut away from your body is not safe. (a) False (b) True
39. 39.True or false: to turn a screw, use a hammer. (a) False (b) True
40. 40.🔧 Which tool would you use to cut a wooden plank? (a) pliers (b) a spirit level (c) a saw (d) a tape measure

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids