Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 29 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🔧 Which tool would you use to check a shelf is level? (a) a spanner (b) a spirit level (c) a tape measure (d) pliers
2. 2.🔧 Which tool would you use to grip and bend wire? (a) a hammer (b) a spanner (c) pliers (d) a hand drill
3. 3.True or false: to drive in a nail, use a tape measure. (a) False (b) True
4. 4.Which job is pliers for? (a) turn a screw (b) check a shelf is level (c) grip and bend wire (d) cut a wooden plank
5. 5.🦺 In the workshop, is it safe to use a cracked tool? (a) not safe (b) safe
6. 6.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) the youngest child (b) a stranger (c) an adult (d) any child alone
7. 7.Which job is a tape measure for? (a) measure a long length (b) smooth a rough edge (c) check a shelf is level (d) measure an angle
8. 8.🔧 Which tool would you use to cut a wooden plank? (a) a spanner (b) pliers (c) a hand drill (d) a saw
9. 9.True or false: to turn a screw, use a screwdriver. (a) True (b) False
10. 10.🔍 Which is the odd one out? (a) touch a hot glue tip (b) use a cracked tool (c) cut towards your hand (d) let adults use hot glue
11. 11.🔍 Which is the odd one out? (a) carry scissors closed (b) let adults use hot glue (c) put tools back after use (d) leave tools on the floor
12. 12.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
13. 13.True or false: to wear safety goggles is safe. (a) True (b) False
14. 14.🦺 In the workshop, is it safe to cut away from your body? (a) safe (b) not safe
15. 15.True or false: to cut towards your hand is not safe. (a) False (b) True
16. 16.True or false: to measure an angle, use a protractor. (a) True (b) False
17. 17.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe
18. 18.🦺 How should you carry scissors? (a) points up, open (b) points down, closed (c) by the blades (d) while running
19. 19.Which job is a hand drill for? (a) measure an angle (b) drive in a nail (c) grip and bend wire (d) make a hole in wood
20. 20.True or false: to cut away from your body is safe. (a) False (b) True
21. 21.True or false: to clamp wood before sawing is not safe. (a) True (b) False
22. 22.True or false: to measure a long length, use a hand drill. (a) True (b) False
23. 23.🔍 Which is the odd one out? (a) tie back long hair (b) clamp wood before sawing (c) touch a hot glue tip (d) put tools back after use
24. 24.True or false: to use a cracked tool is not safe. (a) True (b) False
25. 25.True or false: to clamp wood before sawing is safe. (a) False (b) True
26. 26.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
27. 27.🔧 Which tool would you use to drive in a nail? (a) a hammer (b) a spirit level (c) a saw (d) pliers
28. 28.🔍 Which is the odd one out? (a) wear safety goggles (b) leave tools on the floor (c) use a cracked tool (d) play near a moving drill
29. 29.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
30. 30.🔍 Which is the odd one out? (a) play near a moving drill (b) put tools back after use (c) carry scissors closed (d) cut away from your body
31. 31.True or false: to wear safety goggles is not safe. (a) True (b) False
32. 32.🔧 Which tool would you use to tighten a nut? (a) a spirit level (b) a protractor (c) a hand drill (d) a spanner
33. 33.True or false: to put tools back after use is not safe. (a) True (b) False
34. 34.Which job is a spanner for? (a) cut a wooden plank (b) make a hole in wood (c) tighten a nut (d) grip and bend wire
35. 35.Which job is a saw for? (a) make a hole in wood (b) tighten a nut (c) cut a wooden plank (d) check a shelf is level
36. 36.Which job is sandpaper for? (a) measure an angle (b) smooth a rough edge (c) grip and bend wire (d) turn a screw
37. 37.True or false: to run while holding tools is safe. (a) True (b) False
38. 38.True or false: to touch a hot glue tip is safe. (a) False (b) True
39. 39.True or false: to check a shelf is level, use a spirit level. (a) True (b) False
40. 40.Which job is a spirit level for? (a) cut a wooden plank (b) make a hole in wood (c) grip and bend wire (d) check a shelf is level

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids