Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 327 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.True or false: to cut towards your hand is not safe. (a) True (b) False
2. 2.Which job is a tape measure for? (a) tighten a nut (b) cut a wooden plank (c) check a shelf is level (d) measure a long length
3. 3.🔍 Which is the odd one out? (a) let adults use hot glue (b) run while holding tools (c) leave tools on the floor (d) play near a moving drill
4. 4.True or false: to use a cracked tool is not safe. (a) True (b) False
5. 5.Which job is a spanner for? (a) check a shelf is level (b) tighten a nut (c) turn a screw (d) smooth a rough edge
6. 6.🦺 In the workshop, is it safe to cut towards your hand? (a) not safe (b) safe
7. 7.🦺 How should you carry scissors? (a) points up, open (b) by the blades (c) while running (d) points down, closed
8. 8.True or false: to measure an angle, use a saw. (a) True (b) False
9. 9.🔧 Which tool would you use to check a shelf is level? (a) a spirit level (b) a screwdriver (c) pliers (d) a protractor
10. 10.🔧 Which tool would you use to turn a screw? (a) a hand drill (b) a screwdriver (c) a hammer (d) a spanner
11. 11.🦺 In the workshop, is it safe to clamp wood before sawing? (a) safe (b) not safe
12. 12.🦺 In the workshop, is it safe to put tools back after use? (a) safe (b) not safe
13. 13.🔍 Which is the odd one out? (a) cut towards your hand (b) use a cracked tool (c) touch a hot glue tip (d) tie back long hair
14. 14.True or false: to let adults use hot glue is safe. (a) True (b) False
15. 15.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) the youngest child (b) a stranger (c) any child alone (d) an adult
16. 16.🦺 What protects your eyes when sawing or drilling? (a) nothing (b) sunglasses (c) safety goggles (d) a cap
17. 17.🔍 Which is the odd one out? (a) leave tools on the floor (b) clamp wood before sawing (c) use a cracked tool (d) cut towards your hand
18. 18.Which job is a saw for? (a) tighten a nut (b) measure a long length (c) make a hole in wood (d) cut a wooden plank
19. 19.True or false: to let adults use hot glue is not safe. (a) False (b) True
20. 20.True or false: to tighten a nut, use a screwdriver. (a) True (b) False
21. 21.True or false: to smooth a rough edge, use a screwdriver. (a) True (b) False
22. 22.True or false: to drive in a nail, use a hammer. (a) False (b) True
23. 23.True or false: to carry scissors closed is safe. (a) True (b) False
24. 24.True or false: to run while holding tools is safe. (a) False (b) True
25. 25.🔍 Which is the odd one out? (a) use a cracked tool (b) put tools back after use (c) let adults use hot glue (d) wear safety goggles
26. 26.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
27. 27.🦺 In the workshop, is it safe to wear safety goggles? (a) safe (b) not safe
28. 28.True or false: to wear safety goggles is safe. (a) False (b) True
29. 29.True or false: to cut a wooden plank, use a screwdriver. (a) True (b) False
30. 30.True or false: to touch a hot glue tip is safe. (a) False (b) True
31. 31.🔍 Which is the odd one out? (a) let adults use hot glue (b) leave tools on the floor (c) tie back long hair (d) wear safety goggles
32. 32.🔍 Which is the odd one out? (a) play near a moving drill (b) run while holding tools (c) use a cracked tool (d) wear safety goggles
33. 33.True or false: to touch a hot glue tip is not safe. (a) False (b) True
34. 34.🔧 Which tool would you use to drive in a nail? (a) a spirit level (b) a hammer (c) a tape measure (d) a screwdriver
35. 35.🔧 Which tool would you use to measure a long length? (a) a screwdriver (b) a saw (c) sandpaper (d) a tape measure
36. 36.Which job is a hammer for? (a) drive in a nail (b) measure a long length (c) tighten a nut (d) make a hole in wood
37. 37.Which job is a spirit level for? (a) cut a wooden plank (b) check a shelf is level (c) tighten a nut (d) smooth a rough edge
38. 38.Which job is a hand drill for? (a) smooth a rough edge (b) tighten a nut (c) turn a screw (d) make a hole in wood
39. 39.True or false: to measure a long length, use a tape measure. (a) True (b) False
40. 40.🔍 Which is the odd one out? (a) touch a hot glue tip (b) put tools back after use (c) run while holding tools (d) play near a moving drill

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids