Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 42 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.Which job is a screwdriver for? (a) tighten a nut (b) measure an angle (c) turn a screw (d) drive in a nail
2. 2.🦺 In the workshop, is it safe to cut away from your body? (a) safe (b) not safe
3. 3.🔍 Which is the odd one out? (a) cut towards your hand (b) let adults use hot glue (c) run while holding tools (d) play near a moving drill
4. 4.True or false: to drive in a nail, use a hammer. (a) False (b) True
5. 5.Which job is a spanner for? (a) measure a long length (b) tighten a nut (c) drive in a nail (d) turn a screw
6. 6.True or false: to measure a long length, use a tape measure. (a) False (b) True
7. 7.🔍 Which is the odd one out? (a) cut towards your hand (b) play near a moving drill (c) wear safety goggles (d) use a cracked tool
8. 8.🦺 How should you carry scissors? (a) by the blades (b) points down, closed (c) points up, open (d) while running
9. 9.🔍 Which is the odd one out? (a) cut towards your hand (b) use a cracked tool (c) leave tools on the floor (d) tie back long hair
10. 10.🦺 In the workshop, is it safe to let adults use hot glue? (a) not safe (b) safe
11. 11.True or false: to carry scissors closed is not safe. (a) True (b) False
12. 12.🔧 Which tool would you use to measure an angle? (a) a saw (b) a screwdriver (c) a protractor (d) sandpaper
13. 13.🔍 Which is the odd one out? (a) wear safety goggles (b) cut away from your body (c) clamp wood before sawing (d) touch a hot glue tip
14. 14.🔍 Which is the odd one out? (a) cut towards your hand (b) leave tools on the floor (c) touch a hot glue tip (d) put tools back after use
15. 15.🦺 In the workshop, is it safe to leave tools on the floor? (a) safe (b) not safe
16. 16.🔍 Which is the odd one out? (a) tie back long hair (b) use a cracked tool (c) carry scissors closed (d) let adults use hot glue
17. 17.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) a stranger (b) the youngest child (c) any child alone (d) an adult
18. 18.True or false: to measure an angle, use a tape measure. (a) True (b) False
19. 19.Which job is pliers for? (a) check a shelf is level (b) make a hole in wood (c) measure an angle (d) grip and bend wire
20. 20.Which job is a saw for? (a) check a shelf is level (b) cut a wooden plank (c) smooth a rough edge (d) turn a screw
21. 21.True or false: to measure an angle, use a protractor. (a) False (b) True
22. 22.🔍 Which is the odd one out? (a) let adults use hot glue (b) clamp wood before sawing (c) wear safety goggles (d) play near a moving drill
23. 23.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) safety goggles (c) nothing (d) a cap
24. 24.True or false: to measure a long length, use a screwdriver. (a) True (b) False
25. 25.🦺 In the workshop, is it safe to play near a moving drill? (a) safe (b) not safe
26. 26.🦺 In the workshop, is it safe to use a cracked tool? (a) safe (b) not safe
27. 27.🔧 Which tool would you use to cut a wooden plank? (a) a spirit level (b) a screwdriver (c) a tape measure (d) a saw
28. 28.Which job is a hand drill for? (a) turn a screw (b) make a hole in wood (c) check a shelf is level (d) cut a wooden plank
29. 29.🔧 Which tool would you use to make a hole in wood? (a) a screwdriver (b) a spirit level (c) a saw (d) a hand drill
30. 30.🔍 Which is the odd one out? (a) play near a moving drill (b) leave tools on the floor (c) touch a hot glue tip (d) carry scissors closed
31. 31.True or false: to grip and bend wire, use pliers. (a) True (b) False
32. 32.Which job is a hammer for? (a) measure an angle (b) drive in a nail (c) smooth a rough edge (d) cut a wooden plank
33. 33.🔧 Which tool would you use to smooth a rough edge? (a) a spanner (b) a saw (c) sandpaper (d) a hammer
34. 34.True or false: to check a shelf is level, use a screwdriver. (a) False (b) True
35. 35.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
36. 36.True or false: to drive in a nail, use a tape measure. (a) False (b) True
37. 37.True or false: to make a hole in wood, use a spanner. (a) False (b) True
38. 38.🦺 In the workshop, is it safe to put tools back after use? (a) safe (b) not safe
39. 39.True or false: to leave tools on the floor is not safe. (a) False (b) True
40. 40.Which job is a spirit level for? (a) check a shelf is level (b) make a hole in wood (c) cut a wooden plank (d) tighten a nut

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids