Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 49 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🔧 Which tool would you use to turn a screw? (a) a screwdriver (b) a tape measure (c) a saw (d) a protractor
2. 2.True or false: to make a hole in wood, use a tape measure. (a) True (b) False
3. 3.True or false: to use a cracked tool is not safe. (a) True (b) False
4. 4.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
5. 5.🔍 Which is the odd one out? (a) tie back long hair (b) touch a hot glue tip (c) clamp wood before sawing (d) put tools back after use
6. 6.Which job is a screwdriver for? (a) check a shelf is level (b) smooth a rough edge (c) measure a long length (d) turn a screw
7. 7.🦺 In the workshop, is it safe to cut away from your body? (a) not safe (b) safe
8. 8.True or false: to grip and bend wire, use pliers. (a) True (b) False
9. 9.🔍 Which is the odd one out? (a) tie back long hair (b) carry scissors closed (c) cut towards your hand (d) put tools back after use
10. 10.🦺 What protects your eyes when sawing or drilling? (a) nothing (b) safety goggles (c) a cap (d) sunglasses
11. 11.🔧 Which tool would you use to measure a long length? (a) sandpaper (b) a screwdriver (c) a tape measure (d) a spanner
12. 12.True or false: to play near a moving drill is safe. (a) False (b) True
13. 13.🔍 Which is the odd one out? (a) leave tools on the floor (b) carry scissors closed (c) run while holding tools (d) use a cracked tool
14. 14.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) a stranger (b) any child alone (c) an adult (d) the youngest child
15. 15.True or false: to turn a screw, use a protractor. (a) True (b) False
16. 16.Which job is a saw for? (a) tighten a nut (b) make a hole in wood (c) drive in a nail (d) cut a wooden plank
17. 17.🔧 Which tool would you use to tighten a nut? (a) sandpaper (b) a spanner (c) a hand drill (d) a screwdriver
18. 18.True or false: to measure an angle, use a spirit level. (a) False (b) True
19. 19.Which job is pliers for? (a) tighten a nut (b) smooth a rough edge (c) check a shelf is level (d) grip and bend wire
20. 20.🦺 How should you carry scissors? (a) while running (b) by the blades (c) points down, closed (d) points up, open
21. 21.Which job is a hammer for? (a) measure an angle (b) smooth a rough edge (c) drive in a nail (d) grip and bend wire
22. 22.🦺 In the workshop, is it safe to tie back long hair? (a) not safe (b) safe
23. 23.True or false: to wear safety goggles is safe. (a) True (b) False
24. 24.Which job is a hand drill for? (a) make a hole in wood (b) measure an angle (c) grip and bend wire (d) check a shelf is level
25. 25.Which job is a spanner for? (a) smooth a rough edge (b) tighten a nut (c) grip and bend wire (d) check a shelf is level
26. 26.True or false: to cut towards your hand is safe. (a) True (b) False
27. 27.🔍 Which is the odd one out? (a) leave tools on the floor (b) run while holding tools (c) play near a moving drill (d) cut away from your body
28. 28.🔧 Which tool would you use to cut a wooden plank? (a) a hand drill (b) a tape measure (c) a spirit level (d) a saw
29. 29.🔍 Which is the odd one out? (a) leave tools on the floor (b) wear safety goggles (c) touch a hot glue tip (d) run while holding tools
30. 30.🔍 Which is the odd one out? (a) put tools back after use (b) clamp wood before sawing (c) cut away from your body (d) leave tools on the floor
31. 31.🔧 Which tool would you use to grip and bend wire? (a) a saw (b) pliers (c) sandpaper (d) a hammer
32. 32.🔍 Which is the odd one out? (a) play near a moving drill (b) run while holding tools (c) clamp wood before sawing (d) use a cracked tool
33. 33.True or false: to let adults use hot glue is not safe. (a) True (b) False
34. 34.🔧 Which tool would you use to make a hole in wood? (a) a spanner (b) a hammer (c) a saw (d) a hand drill
35. 35.True or false: to leave tools on the floor is not safe. (a) True (b) False
36. 36.True or false: to measure an angle, use a protractor. (a) False (b) True
37. 37.True or false: to put tools back after use is safe. (a) False (b) True
38. 38.True or false: to measure a long length, use a hammer. (a) True (b) False
39. 39.True or false: to tighten a nut, use a spanner. (a) True (b) False
40. 40.🦺 In the workshop, is it safe to carry scissors closed? (a) safe (b) not safe

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids