Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 7 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.Which job is a spanner for? (a) measure a long length (b) grip and bend wire (c) smooth a rough edge (d) tighten a nut
2. 2.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) a stranger (b) the youngest child (c) an adult (d) any child alone
3. 3.True or false: to clamp wood before sawing is safe. (a) False (b) True
4. 4.🦺 In the workshop, is it safe to touch a hot glue tip? (a) not safe (b) safe
5. 5.🦺 What protects your eyes when sawing or drilling? (a) safety goggles (b) sunglasses (c) nothing (d) a cap
6. 6.🦺 In the workshop, is it safe to let adults use hot glue? (a) not safe (b) safe
7. 7.🔧 Which tool would you use to make a hole in wood? (a) a hand drill (b) a saw (c) a screwdriver (d) a spanner
8. 8.🔍 Which is the odd one out? (a) put tools back after use (b) wear safety goggles (c) cut away from your body (d) play near a moving drill
9. 9.🔍 Which is the odd one out? (a) let adults use hot glue (b) cut away from your body (c) wear safety goggles (d) leave tools on the floor
10. 10.Which job is a hand drill for? (a) grip and bend wire (b) drive in a nail (c) make a hole in wood (d) check a shelf is level
11. 11.🦺 In the workshop, is it safe to cut towards your hand? (a) not safe (b) safe
12. 12.🔍 Which is the odd one out? (a) use a cracked tool (b) tie back long hair (c) play near a moving drill (d) leave tools on the floor
13. 13.Which job is a saw for? (a) cut a wooden plank (b) drive in a nail (c) turn a screw (d) tighten a nut
14. 14.🦺 In the workshop, is it safe to cut away from your body? (a) not safe (b) safe
15. 15.True or false: to put tools back after use is safe. (a) False (b) True
16. 16.True or false: to make a hole in wood, use a hand drill. (a) False (b) True
17. 17.Which job is a spirit level for? (a) measure an angle (b) measure a long length (c) make a hole in wood (d) check a shelf is level
18. 18.🦺 In the workshop, is it safe to put tools back after use? (a) safe (b) not safe
19. 19.🔍 Which is the odd one out? (a) leave tools on the floor (b) cut towards your hand (c) run while holding tools (d) carry scissors closed
20. 20.🦺 In the workshop, is it safe to clamp wood before sawing? (a) not safe (b) safe
21. 21.Which job is sandpaper for? (a) grip and bend wire (b) turn a screw (c) measure an angle (d) smooth a rough edge
22. 22.Which job is a tape measure for? (a) measure a long length (b) cut a wooden plank (c) smooth a rough edge (d) grip and bend wire
23. 23.🔧 Which tool would you use to tighten a nut? (a) a hammer (b) sandpaper (c) a spanner (d) a screwdriver
24. 24.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
25. 25.True or false: to clamp wood before sawing is not safe. (a) True (b) False
26. 26.🔧 Which tool would you use to measure an angle? (a) a screwdriver (b) a protractor (c) sandpaper (d) a saw
27. 27.🔧 Which tool would you use to measure a long length? (a) pliers (b) a spanner (c) a tape measure (d) a screwdriver
28. 28.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
29. 29.Which job is a screwdriver for? (a) tighten a nut (b) grip and bend wire (c) check a shelf is level (d) turn a screw
30. 30.🦺 How should you carry scissors? (a) points down, closed (b) by the blades (c) while running (d) points up, open
31. 31.🦺 In the workshop, is it safe to leave tools on the floor? (a) not safe (b) safe
32. 32.🔧 Which tool would you use to drive in a nail? (a) a spanner (b) a spirit level (c) pliers (d) a hammer
33. 33.True or false: to run while holding tools is not safe. (a) True (b) False
34. 34.🔍 Which is the odd one out? (a) run while holding tools (b) cut away from your body (c) clamp wood before sawing (d) let adults use hot glue
35. 35.🔍 Which is the odd one out? (a) put tools back after use (b) carry scissors closed (c) cut towards your hand (d) let adults use hot glue
36. 36.Which job is a hammer for? (a) drive in a nail (b) check a shelf is level (c) measure a long length (d) make a hole in wood
37. 37.True or false: to drive in a nail, use a spirit level. (a) False (b) True
38. 38.🔧 Which tool would you use to smooth a rough edge? (a) a hand drill (b) a hammer (c) a tape measure (d) sandpaper
39. 39.True or false: to let adults use hot glue is not safe. (a) True (b) False
40. 40.🦺 In the workshop, is it safe to carry scissors closed? (a) not safe (b) safe

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids