← Tools and workshop safety lesson New set →

Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 122 · 40 questions
TalentJR

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

NameDateTime takenScore ___ / 40
  1. 1.True or false: to let adults use hot glue is not safe. (a) False (b) True
  2. 2.🔍 Which is the odd one out? (a) put tools back after use (b) cut away from your body (c) let adults use hot glue (d) use a cracked tool
  3. 3.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
  4. 4.🔧 Which tool would you use to drive in a nail? (a) pliers (b) a hand drill (c) a hammer (d) sandpaper
  5. 5.🔍 Which is the odd one out? (a) touch a hot glue tip (b) cut towards your hand (c) use a cracked tool (d) wear safety goggles
  6. 6.🔍 Which is the odd one out? (a) cut away from your body (b) wear safety goggles (c) leave tools on the floor (d) carry scissors closed
  7. 7.🔧 Which tool would you use to turn a screw? (a) a hand drill (b) a spanner (c) a saw (d) a screwdriver
  8. 8.True or false: to measure an angle, use pliers. (a) True (b) False
  9. 9.🦺 How should you carry scissors? (a) while running (b) points down, closed (c) points up, open (d) by the blades
  10. 10.Which job is a screwdriver for? (a) make a hole in wood (b) measure a long length (c) smooth a rough edge (d) turn a screw
  11. 11.Which job is sandpaper for? (a) grip and bend wire (b) smooth a rough edge (c) turn a screw (d) drive in a nail
  12. 12.🔧 Which tool would you use to cut a wooden plank? (a) a tape measure (b) a saw (c) a hand drill (d) a hammer
  13. 13.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) safety goggles (c) a cap (d) nothing
  14. 14.True or false: to clamp wood before sawing is not safe. (a) False (b) True
  15. 15.Which job is a hammer for? (a) make a hole in wood (b) drive in a nail (c) tighten a nut (d) grip and bend wire
  16. 16.Which job is a tape measure for? (a) measure an angle (b) smooth a rough edge (c) turn a screw (d) measure a long length
  17. 17.🦺 In the workshop, is it safe to use a cracked tool? (a) safe (b) not safe
  18. 18.True or false: to make a hole in wood, use a spanner. (a) True (b) False
  19. 19.🦺 In the workshop, is it safe to clamp wood before sawing? (a) safe (b) not safe
  20. 20.True or false: to measure a long length, use pliers. (a) False (b) True
  21. 21.True or false: to tie back long hair is safe. (a) False (b) True
  22. 22.🔍 Which is the odd one out? (a) run while holding tools (b) leave tools on the floor (c) tie back long hair (d) play near a moving drill
  23. 23.True or false: to use a cracked tool is safe. (a) False (b) True
  24. 24.True or false: to carry scissors closed is safe. (a) True (b) False
  25. 25.🔧 Which tool would you use to smooth a rough edge? (a) a hand drill (b) a tape measure (c) a saw (d) sandpaper
  26. 26.🦺 In the workshop, is it safe to cut towards your hand? (a) safe (b) not safe
  27. 27.Which job is a protractor for? (a) measure a long length (b) drive in a nail (c) grip and bend wire (d) measure an angle
  28. 28.🔍 Which is the odd one out? (a) touch a hot glue tip (b) use a cracked tool (c) play near a moving drill (d) put tools back after use
  29. 29.Which job is a spanner for? (a) cut a wooden plank (b) check a shelf is level (c) turn a screw (d) tighten a nut
  30. 30.True or false: to play near a moving drill is safe. (a) True (b) False
  31. 31.🦺 In the workshop, is it safe to play near a moving drill? (a) safe (b) not safe
  32. 32.🦺 In the workshop, is it safe to carry scissors closed? (a) safe (b) not safe
  33. 33.True or false: to measure a long length, use a saw. (a) False (b) True
  34. 34.True or false: to put tools back after use is safe. (a) False (b) True
  35. 35.🦺 In the workshop, is it safe to touch a hot glue tip? (a) not safe (b) safe
  36. 36.True or false: to run while holding tools is safe. (a) False (b) True
  37. 37.True or false: to make a hole in wood, use a hand drill. (a) False (b) True
  38. 38.True or false: to smooth a rough edge, use sandpaper. (a) False (b) True
  39. 39.True or false: to cut towards your hand is safe. (a) False (b) True
  40. 40.True or false: to touch a hot glue tip is safe. (a) False (b) True

Answer key

  1. False
  2. use a cracked tool
  3. safe
  4. a hammer
  5. wear safety goggles
  6. leave tools on the floor
  7. a screwdriver
  8. False
  9. points down, closed
  10. turn a screw
  11. smooth a rough edge
  12. a saw
  13. safety goggles
  14. False
  15. drive in a nail
  16. measure a long length
  17. not safe
  18. False
  19. safe
  20. False
  21. True
  22. tie back long hair
  23. False
  24. True
  25. sandpaper
  26. not safe
  27. measure an angle
  28. put tools back after use
  29. tighten a nut
  30. False
  31. not safe
  32. safe
  33. False
  34. True
  35. not safe
  36. False
  37. True
  38. True
  39. False
  40. False

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids