Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 123 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.🔍 Which is the odd one out? (a) put tools back after use (b) let adults use hot glue (c) cut towards your hand (d) cut away from your body
2. 2.🦺 In the workshop, is it safe to run while holding tools? (a) not safe (b) safe
3. 3.🔍 Which is the odd one out? (a) leave tools on the floor (b) clamp wood before sawing (c) carry scissors closed (d) cut away from your body
4. 4.🔧 Which tool would you use to smooth a rough edge? (a) sandpaper (b) pliers (c) a screwdriver (d) a hammer
5. 5.🔍 Which is the odd one out? (a) run while holding tools (b) play near a moving drill (c) clamp wood before sawing (d) cut towards your hand
6. 6.True or false: to clamp wood before sawing is safe. (a) True (b) False
7. 7.🔧 Which tool would you use to cut a wooden plank? (a) pliers (b) a saw (c) a hammer (d) a hand drill
8. 8.True or false: to carry scissors closed is safe. (a) False (b) True
9. 9.🦺 In the workshop, is it safe to cut away from your body? (a) not safe (b) safe
10. 10.Which job is a protractor for? (a) make a hole in wood (b) measure a long length (c) measure an angle (d) cut a wooden plank
11. 11.True or false: to run while holding tools is safe. (a) True (b) False
12. 12.Which job is a hand drill for? (a) grip and bend wire (b) make a hole in wood (c) tighten a nut (d) check a shelf is level
13. 13.True or false: to smooth a rough edge, use sandpaper. (a) False (b) True
14. 14.Which job is sandpaper for? (a) measure an angle (b) smooth a rough edge (c) check a shelf is level (d) drive in a nail
15. 15.🔍 Which is the odd one out? (a) use a cracked tool (b) touch a hot glue tip (c) put tools back after use (d) cut towards your hand
16. 16.True or false: to let adults use hot glue is safe. (a) False (b) True
17. 17.True or false: to play near a moving drill is not safe. (a) False (b) True
18. 18.Which job is a spanner for? (a) tighten a nut (b) drive in a nail (c) turn a screw (d) smooth a rough edge
19. 19.True or false: to touch a hot glue tip is safe. (a) False (b) True
20. 20.True or false: to tie back long hair is not safe. (a) True (b) False
21. 21.True or false: to make a hole in wood, use a screwdriver. (a) True (b) False
22. 22.🔧 Which tool would you use to tighten a nut? (a) a spirit level (b) a spanner (c) a hammer (d) pliers
23. 23.True or false: to check a shelf is level, use a spirit level. (a) False (b) True
24. 24.🔍 Which is the odd one out? (a) leave tools on the floor (b) cut away from your body (c) play near a moving drill (d) run while holding tools
25. 25.🦺 In the workshop, is it safe to play near a moving drill? (a) not safe (b) safe
26. 26.🦺 In the workshop, is it safe to leave tools on the floor? (a) safe (b) not safe
27. 27.🦺 In the workshop, is it safe to wear safety goggles? (a) not safe (b) safe
28. 28.🔍 Which is the odd one out? (a) clamp wood before sawing (b) put tools back after use (c) play near a moving drill (d) tie back long hair
29. 29.True or false: to make a hole in wood, use a spanner. (a) True (b) False
30. 30.True or false: to drive in a nail, use a hammer. (a) True (b) False
31. 31.True or false: to measure a long length, use sandpaper. (a) False (b) True
32. 32.🔍 Which is the odd one out? (a) cut towards your hand (b) run while holding tools (c) leave tools on the floor (d) let adults use hot glue
33. 33.🔍 Which is the odd one out? (a) cut towards your hand (b) wear safety goggles (c) use a cracked tool (d) play near a moving drill
34. 34.🔧 Which tool would you use to measure a long length? (a) a hand drill (b) pliers (c) a screwdriver (d) a tape measure
35. 35.🔧 Which tool would you use to measure an angle? (a) a hand drill (b) a hammer (c) a protractor (d) sandpaper
36. 36.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) a stranger (c) an adult (d) the youngest child
37. 37.True or false: to grip and bend wire, use a screwdriver. (a) False (b) True
38. 38.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
39. 39.🦺 What protects your eyes when sawing or drilling? (a) sunglasses (b) nothing (c) a cap (d) safety goggles
40. 40.🔍 Which is the odd one out? (a) tie back long hair (b) run while holding tools (c) touch a hot glue tip (d) leave tools on the floor

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids