← Tools and workshop safety lesson New set →

Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 203 · 40 questions
TalentJR

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

NameDateTime takenScore ___ / 40
  1. 1.Which job is a hand drill for? (a) smooth a rough edge (b) cut a wooden plank (c) drive in a nail (d) make a hole in wood
  2. 2.🔧 Which tool would you use to make a hole in wood? (a) a saw (b) a spirit level (c) a tape measure (d) a hand drill
  3. 3.True or false: to let adults use hot glue is safe. (a) False (b) True
  4. 4.🔧 Which tool would you use to grip and bend wire? (a) sandpaper (b) a tape measure (c) a screwdriver (d) pliers
  5. 5.True or false: to drive in a nail, use a spanner. (a) False (b) True
  6. 6.🦺 In the workshop, is it safe to leave tools on the floor? (a) safe (b) not safe
  7. 7.🦺 How should you carry scissors? (a) points up, open (b) points down, closed (c) by the blades (d) while running
  8. 8.True or false: to run while holding tools is safe. (a) True (b) False
  9. 9.True or false: to grip and bend wire, use a spanner. (a) False (b) True
  10. 10.True or false: to measure an angle, use a spirit level. (a) True (b) False
  11. 11.True or false: to play near a moving drill is safe. (a) True (b) False
  12. 12.True or false: to cut a wooden plank, use a saw. (a) False (b) True
  13. 13.True or false: to tighten a nut, use a spanner. (a) False (b) True
  14. 14.🔍 Which is the odd one out? (a) run while holding tools (b) carry scissors closed (c) leave tools on the floor (d) cut towards your hand
  15. 15.Which job is a saw for? (a) smooth a rough edge (b) cut a wooden plank (c) drive in a nail (d) tighten a nut
  16. 16.🔍 Which is the odd one out? (a) play near a moving drill (b) leave tools on the floor (c) run while holding tools (d) tie back long hair
  17. 17.🔧 Which tool would you use to turn a screw? (a) a screwdriver (b) a hammer (c) a protractor (d) sandpaper
  18. 18.🦺 In the workshop, is it safe to tie back long hair? (a) not safe (b) safe
  19. 19.🦺 In the workshop, is it safe to wear safety goggles? (a) safe (b) not safe
  20. 20.True or false: to cut a wooden plank, use sandpaper. (a) False (b) True
  21. 21.🔍 Which is the odd one out? (a) let adults use hot glue (b) carry scissors closed (c) tie back long hair (d) leave tools on the floor
  22. 22.True or false: to make a hole in wood, use a tape measure. (a) True (b) False
  23. 23.True or false: to leave tools on the floor is safe. (a) True (b) False
  24. 24.True or false: to wear safety goggles is safe. (a) False (b) True
  25. 25.🔍 Which is the odd one out? (a) carry scissors closed (b) tie back long hair (c) cut towards your hand (d) clamp wood before sawing
  26. 26.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) an adult (b) the youngest child (c) any child alone (d) a stranger
  27. 27.🔍 Which is the odd one out? (a) cut away from your body (b) tie back long hair (c) touch a hot glue tip (d) put tools back after use
  28. 28.True or false: to check a shelf is level, use pliers. (a) True (b) False
  29. 29.🔧 Which tool would you use to measure an angle? (a) a hand drill (b) a protractor (c) sandpaper (d) pliers
  30. 30.True or false: to grip and bend wire, use a hand drill. (a) False (b) True
  31. 31.🔧 Which tool would you use to drive in a nail? (a) a spirit level (b) pliers (c) a hammer (d) a spanner
  32. 32.🔍 Which is the odd one out? (a) play near a moving drill (b) run while holding tools (c) leave tools on the floor (d) put tools back after use
  33. 33.Which job is a spirit level for? (a) check a shelf is level (b) measure a long length (c) measure an angle (d) make a hole in wood
  34. 34.🔧 Which tool would you use to measure a long length? (a) a tape measure (b) a hammer (c) sandpaper (d) a screwdriver
  35. 35.🔧 Which tool would you use to tighten a nut? (a) pliers (b) a hand drill (c) a screwdriver (d) a spanner
  36. 36.🔍 Which is the odd one out? (a) play near a moving drill (b) cut away from your body (c) use a cracked tool (d) run while holding tools
  37. 37.True or false: to use a cracked tool is not safe. (a) True (b) False
  38. 38.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
  39. 39.True or false: to play near a moving drill is not safe. (a) True (b) False
  40. 40.True or false: to measure a long length, use a tape measure. (a) True (b) False

Answer key

  1. make a hole in wood
  2. a hand drill
  3. True
  4. pliers
  5. False
  6. not safe
  7. points down, closed
  8. False
  9. False
  10. False
  11. False
  12. True
  13. True
  14. carry scissors closed
  15. cut a wooden plank
  16. tie back long hair
  17. a screwdriver
  18. safe
  19. safe
  20. False
  21. leave tools on the floor
  22. False
  23. False
  24. True
  25. cut towards your hand
  26. an adult
  27. touch a hot glue tip
  28. False
  29. a protractor
  30. False
  31. a hammer
  32. put tools back after use
  33. check a shelf is level
  34. a tape measure
  35. a spanner
  36. cut away from your body
  37. True
  38. safe
  39. True
  40. True

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids