Engineering Worksheet: Tools and Safety

Engineering lesson 7: Tools and workshop safety · Set 323 · 40 questions

Engineer's tip (Right tool, safe hands): Measure → tape measure, protractor · level → spirit level · cut → saw · nails → hammer. Screws → screwdriver · nuts → spanner · holes → drill · wire → pliers · smooth → sandpaper. Safe: goggles, tied hair, clamps, tidy bench, cut away from you, adult for hot or power tools.

1. 1.Which job is a spirit level for? (a) make a hole in wood (b) cut a wooden plank (c) check a shelf is level (d) measure an angle
2. 2.🦺 In the workshop, is it safe to run while holding tools? (a) safe (b) not safe
3. 3.🦺 What protects your eyes when sawing or drilling? (a) a cap (b) nothing (c) sunglasses (d) safety goggles
4. 4.🔧 Which tool would you use to check a shelf is level? (a) pliers (b) a screwdriver (c) a protractor (d) a spirit level
5. 5.🔧 Which tool would you use to grip and bend wire? (a) sandpaper (b) pliers (c) a protractor (d) a spirit level
6. 6.🦺 How should you carry scissors? (a) points down, closed (b) by the blades (c) while running (d) points up, open
7. 7.🔍 Which is the odd one out? (a) tie back long hair (b) leave tools on the floor (c) put tools back after use (d) cut away from your body
8. 8.🔧 Which tool would you use to measure an angle? (a) pliers (b) a protractor (c) a tape measure (d) a saw
9. 9.True or false: to measure an angle, use a protractor. (a) True (b) False
10. 10.🦺 In the workshop, is it safe to cut towards your hand? (a) not safe (b) safe
11. 11.True or false: to cut a wooden plank, use a screwdriver. (a) True (b) False
12. 12.Which job is a screwdriver for? (a) make a hole in wood (b) grip and bend wire (c) turn a screw (d) tighten a nut
13. 13.True or false: to cut towards your hand is not safe. (a) True (b) False
14. 14.True or false: to run while holding tools is not safe. (a) False (b) True
15. 15.True or false: to measure a long length, use a tape measure. (a) False (b) True
16. 16.🦺 In the workshop, is it safe to put tools back after use? (a) not safe (b) safe
17. 17.🔍 Which is the odd one out? (a) clamp wood before sawing (b) carry scissors closed (c) put tools back after use (d) touch a hot glue tip
18. 18.🦺 In the workshop, is it safe to tie back long hair? (a) safe (b) not safe
19. 19.True or false: to cut away from your body is safe. (a) False (b) True
20. 20.True or false: to put tools back after use is not safe. (a) True (b) False
21. 21.🦺 In the workshop, is it safe to let adults use hot glue? (a) safe (b) not safe
22. 22.True or false: to tighten a nut, use a spanner. (a) False (b) True
23. 23.🔧 Which tool would you use to make a hole in wood? (a) a saw (b) a spirit level (c) a tape measure (d) a hand drill
24. 24.True or false: to play near a moving drill is safe. (a) True (b) False
25. 25.True or false: to grip and bend wire, use a screwdriver. (a) False (b) True
26. 26.🔍 Which is the odd one out? (a) tie back long hair (b) let adults use hot glue (c) play near a moving drill (d) cut away from your body
27. 27.🦺 In the workshop, is it safe to leave tools on the floor? (a) not safe (b) safe
28. 28.🔍 Which is the odd one out? (a) clamp wood before sawing (b) put tools back after use (c) wear safety goggles (d) run while holding tools
29. 29.Which job is a protractor for? (a) grip and bend wire (b) smooth a rough edge (c) check a shelf is level (d) measure an angle
30. 30.Which job is a hand drill for? (a) turn a screw (b) cut a wooden plank (c) smooth a rough edge (d) make a hole in wood
31. 31.🔍 Which is the odd one out? (a) leave tools on the floor (b) touch a hot glue tip (c) run while holding tools (d) wear safety goggles
32. 32.🔧 Which tool would you use to tighten a nut? (a) a saw (b) a spanner (c) a hand drill (d) a spirit level
33. 33.True or false: to drive in a nail, use a hammer. (a) False (b) True
34. 34.🦺 In the workshop, is it safe to touch a hot glue tip? (a) safe (b) not safe
35. 35.🦺 Who should use hot glue guns and power tools in a kids’ project? (a) any child alone (b) the youngest child (c) an adult (d) a stranger
36. 36.True or false: to clamp wood before sawing is not safe. (a) False (b) True
37. 37.True or false: to check a shelf is level, use a saw. (a) False (b) True
38. 38.True or false: to touch a hot glue tip is not safe. (a) False (b) True
39. 39.True or false: to touch a hot glue tip is safe. (a) False (b) True
40. 40.Which job is a tape measure for? (a) cut a wooden plank (b) turn a screw (c) measure a long length (d) drive in a nail

Free engineering lessons, practice and worksheets at talentjr.in/engineering-for-kids